Gigabyte GA-965GM-S2, GA-965GM-DS2 user manual Install Drivers, Install Chipset Drivers

Page 47

Chapter 3 Install Drivers

Pictures below are shown in Windows XP.

Insert the driver CD-title that came with your motherboard into your CD-ROM drive, the driver CD-title will auto start and show the installation guide. If not, please double click the CD-ROM device icon in "My computer", and execute the Run.exe.

3-1 Install Chipset Drivers

After insert the driver CD, "Xpress Install" will scan automatically the system and then list all the drivers that recommended to install. Please pick the item that you want and press "install" followed the item; or you can press "Xpress Install" to install all items defaulted.

Some device drivers will restart your system automatically. After restarting your system the "Xpress Install" will continue to install other drivers.

System will reboot automatically after install the drivers, afterward you can install others application.

For USB2.0 driver support under Windows XP operating system, please use Windows Service Pack. After install Windows Service Pack, it will show a question mark "?" in "Universal Serial Bus controller" under "Device Manager". Please remove the question mark and restart the system (System will auto-detect the right USB2.0 driver).

English

- 47 -

Install Drivers

Image 47

Contents GA-965GM-DS2 / GA-965GM-S2 Motherboard GA-965GM-DS2 GA-965GM-S2 Product Manual Classification CopyrightTable of Contents Install Drivers Item Checklist Kbms ATX12VLGA775 Block Diagram Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryMbit flash ROM Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction MIC Connectors IntroductionLine Out Front Speaker Out ATX12V/ATX Power Connector IDE IDE Connector Cpufan / Sysfan Cooler Fan Power ConnectorFDD FDD Connector Pwrled Fpanel Front Panel Jumper Faudio Front Audio Connector Spdifio Spdif In/Out Connector Cdin CD In Connector15 F11394 / F21394 Ieee 1394 Connector FUSB1 / FUSB2 / FUSB3 Front USB ConnectorsCI Chassis Intrusion, Case Open Comb Comb ConnectorClrcmos Clear Cmos BatteryMain Menu Status Page Setup Menu / Option Page Setup MenuF12 Boot Menu Main Menu For example GA-965GM-DS2 Bios Ver. F1„ PnP/PCI Configurations „ Standard Cmos Features„ Advanced Bios Features „ Power Management SetupIDE Channel 2/3 Master, IDE Channel 4/5 Master, Slave TimeIDE Channel 0/1 Master Memory Floppy 3 Mode Support for Japan AreaDrive a Halt onPassword Check Hard Disk Boot PriorityFirst / Second / Third Boot Device No-Execute Memory ProtectNote HDD S.M.A.R.T. CapabilityCPU Hyper-Threading Note Limit Cpuid Max. to 3 NoteIntegrated Peripherals Onboard H/W LAN Smart LAN LAN Cable Diagnostic FunctionOnboard H/W Onboard SATA/IDE Device OnBoard LAN Boot ROMOnBoard SATA/IDE Ctrl Mode Parallel Port ModePME Event Wake Up Power On by RingResume by Alarm Power On By MousePnP/PCI Configurations Current VoltageV Vcore/DDR18V/+3.3V/+12V Current System/CPU TemperatureCPU Warning Temperature Case OpenedSmart FAN Control Method Note Smart FAN Control ModeMemory Frequency Mhz CPU Clock Ratio NoteSystem Memory Multiplier Load Fail-Safe Defaults Set Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Install DriversDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Boot from CD/DVD F9 Xpress Recovery2Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Installing Sata hard drives in your computer RAID/IDE Step Save and exit Bios Setup Configuring RAID array in RAID Bios Steps Create ArrayJraid RDD0 Jraid Status MembersHDDx Delete Array Cd bootdrv Menu Making a Sata Driver Disk Required for Ahci and RAID ModeWindows Setup ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English English English Taiwan Headquarters Contact UsGigabyte Global Service System