Gigabyte GA-965GM-S2 Entering the Q-FlashTMutility, Task menu for Dual Bios utility, Action bar

Page 55

Entering the Q-FlashTMutility:

Step1: To use Q-Flash utility, you must press Del in the boot screen to enter BIOS menu.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Select Language
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Set Supervisor Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Dual BIOS/Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

Step 2: Press F8 button on your keyboard and then Y button to enter the Dual BIOS/Q-Flash utility.

Exploring the Q-FlashTM / Dual BIOS utility screen

The Q-Flash / Dual BIOS utility screen consists of the following key components.

English

Task menu for Dual BIOS utility

Task menu for Q-FlashTMutility

									Dual BIOS utility bar
			Dual BIOS Utility
			Dual BIOS Utility

		Boot From		Main Bios
		Main ROM Type/Size		SST 49LF003A		512K
		Backup ROM Type/Size		SST 49LF003A		512K
		Wide Range Protection		Disable
			Boot From	Main Bios
			Auto Recovery	Enable
			Halt On Error	Disable
			Copy Main ROM Data to Backup
			Load Default Settings
			Save Settings to CMOS						Q-FlashTMutility title
			Save Settings to CMOS
			Q-Flash Utility
			Q-Flash Utility
			Load Main BIOS from Floppy						bar
			Load Backup BIOS from Floppy						bar
			Save Main BIOS to Floppy
			Save Backup BIOS to Floppy						Action bar
			Save Backup BIOS to Floppy
		Enter : Run	:Move	ESC:Reset	F10:Power Off
		Enter : Run	:Move	ESC:Reset	F10:Power Off

Task menu for Dual BIOS utility:

Contains the names of eight tasks and two item showing information about the BIOS ROM type. Blocking a task and pressing Enter key on your keyboard to enable execution of the task.

Task menu for Q-Flash utility:

Contains the names of four tasks. Blocking a task and pressing Enter key on your keyboard to enable execu- tion of the task.

Action bar:

Contains the names of four actions needed to operate the Q-Flash/Dual BIOS utility. Pressing the buttons mentioned on your keyboards to perform these actions.

- 55 -

Appendix

Image 55

Contents GA-965GM-DS2 / GA-965GM-S2 Motherboard GA-965GM-DS2 GA-965GM-S2 Product Manual Classification CopyrightTable of Contents Install Drivers Item Checklist Kbms ATX12VLGA775 Block Diagram Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryMbit flash ROM Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Line Out Front Speaker Out Connectors IntroductionMIC ATX12V/ATX Power Connector IDE IDE Connector Cpufan / Sysfan Cooler Fan Power ConnectorFDD FDD Connector Pwrled Fpanel Front Panel Jumper Faudio Front Audio Connector Spdifio Spdif In/Out Connector Cdin CD In Connector15 F11394 / F21394 Ieee 1394 Connector FUSB1 / FUSB2 / FUSB3 Front USB ConnectorsCI Chassis Intrusion, Case Open Comb Comb ConnectorClrcmos Clear Cmos BatteryMain Menu Status Page Setup Menu / Option Page Setup MenuF12 Boot Menu Main Menu For example GA-965GM-DS2 Bios Ver. F1„ PnP/PCI Configurations „ Standard Cmos Features„ Advanced Bios Features „ Power Management SetupIDE Channel 0/1 Master TimeIDE Channel 2/3 Master, IDE Channel 4/5 Master, Slave Memory Floppy 3 Mode Support for Japan AreaDrive a Halt onFirst / Second / Third Boot Device Hard Disk Boot PriorityPassword Check No-Execute Memory ProtectNote HDD S.M.A.R.T. CapabilityCPU Hyper-Threading Note Limit Cpuid Max. to 3 NoteIntegrated Peripherals Onboard H/W Smart LAN LAN Cable Diagnostic FunctionOnboard H/W LAN Onboard SATA/IDE Device OnBoard LAN Boot ROMOnBoard SATA/IDE Ctrl Mode Parallel Port ModePME Event Wake Up Power On by RingResume by Alarm Power On By MousePnP/PCI Configurations Current VoltageV Vcore/DDR18V/+3.3V/+12V Current System/CPU TemperatureCPU Warning Temperature Case OpenedSmart FAN Control Method Note Smart FAN Control ModeSystem Memory Multiplier CPU Clock Ratio NoteMemory Frequency Mhz Load Fail-Safe Defaults Set Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Install DriversDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Boot from CD/DVD F9 Xpress Recovery2Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Installing Sata hard drives in your computer RAID/IDE Step Save and exit Bios Setup Configuring RAID array in RAID Bios Steps Create ArrayJraid RDD0 Jraid Status MembersHDDx Delete Array Cd bootdrv Menu Making a Sata Driver Disk Required for Ahci and RAID ModeWindows Setup ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English English English Taiwan Headquarters Contact UsGigabyte Global Service System