Gigabyte GA-965GM-DS2, GA-965GM-S2 user manual Configuring RAID array in RAID Bios

Page 66

English

(3) Configuring RAID array in RAID BIOS

Enter the RAID BIOS setup utility to configure a RAID array. Skip this step if you do not want to create RAID.

Step 1:

After the POST memory test begins and before the operating system boot begins, look for a message which says "Press <Ctrl-G> to enter RAID Setup Utility" (Figure 3). Press CTRL+ G to enter the GIGABYTE SATA2 RAID BIOS setup utility.

GIGA-BYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS v1.06.53

Copyright (C) 2005 GIGA-BYTE Technology. http://www.giga-byte.com

HDD0

:

ST3120026AS

120 GB

Non-RAID

HDD1

:

ST3120026AS

120 GB

Non-RAID

Press <Ctrl-G> to enter RAID Setup Utility ...

Figure 3

In the main screen of the GIGABYTE SATA2 RAID BIOS utility (Figure 4), use the UP or DOWN ARROW key to highlight through choices. Highlight the item that you wish to execute and press ENTER.

GIGA-BYTE Technology Corp. PCIE-to-SATAII/IDE RAID Controller BIOS V1.06.53

[ Main Menu ]

[ Hard Disk Drive List ]

 

 

Create RAID Disk Drive

Mode Name

Capacity

Type/Status

Delete RAID Disk Drive

HDD0: ST3120026AS

120 GB

Non-RAID

Revert HDD to Non-RAID

HDD1: ST3120026AS

120 GB

Non-RAID

Solve Mirror Conflict

 

 

 

Rebuild Mirror Drive

 

 

 

Save And Exit Setup

 

 

 

Exit Without Saving

 

 

 

[ RAID Disk Drive List ]

 

 

 

[

TAB]-Switch Window

[ ]-Select ITEM

[ENTER]-Action

[ESC]-Exit

 

 

 

 

 

Figure 4

Note: In the main screen, you can select a hard disk in the Hard Disk Drive List block and press ENTER. This allows you to check detailed information about the selected hard disk.

GA-965GM-(D)S2 Motherboard

- 66 -

Page 65 Page 67
Image 66
Page 65 Page 67
Contents GA-965GM-DS2 / GA-965GM-S2 Motherboard GA-965GM-DS2 GA-965GM-S2 Copyright Product Manual ClassificationTable of Contents Install Drivers Item Checklist Kbms ATX12VLGA775 Block Diagram Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUMbit flash ROM Installation of the CPU and CPU Cooler Installation of the CPUInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Line Out Front Speaker OutMIC ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector IDE IDE ConnectorFDD FDD Connector Pwrled Fpanel Front Panel Jumper Faudio Front Audio Connector Cdin CD In Connector Spdifio Spdif In/Out ConnectorFUSB1 / FUSB2 / FUSB3 Front USB Connectors 15 F11394 / F21394 Ieee 1394 ConnectorComb Comb Connector CI Chassis Intrusion, Case OpenBattery Clrcmos Clear CmosStatus Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example GA-965GM-DS2 Bios Ver. F1 F12 Boot Menu„ Power Management Setup „ Standard Cmos Features„ Advanced Bios Features „ PnP/PCI ConfigurationsTime IDE Channel 0/1 MasterIDE Channel 2/3 Master, IDE Channel 4/5 Master, Slave Halt on Floppy 3 Mode Support for Japan AreaDrive a MemoryHard Disk Boot Priority First / Second / Third Boot DevicePassword Check Limit Cpuid Max. to 3 Note HDD S.M.A.R.T. CapabilityCPU Hyper-Threading Note No-Execute Memory ProtectNoteIntegrated Peripherals Smart LAN LAN Cable Diagnostic Function Onboard H/WOnboard H/W LAN Parallel Port Mode OnBoard LAN Boot ROMOnBoard SATA/IDE Ctrl Mode Onboard SATA/IDE DevicePower On By Mouse Power On by RingResume by Alarm PME Event Wake UpPnP/PCI Configurations Case Opened Current System/CPU TemperatureCPU Warning Temperature Current VoltageV Vcore/DDR18V/+3.3V/+12VSmart FAN Control Mode Smart FAN Control Method NoteCPU Clock Ratio Note System Memory MultiplierMemory Frequency Mhz Load Fail-Safe Defaults Set Supervisor/User Password Save & Exit Setup Exit Without SavingInstall Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Boot from CD/DVD F9 Xpress Recovery2 Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 System requirementsMain Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to 4 to flash the backup BIOS, too Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Installing Sata hard drives in your computer RAID/IDE Step Save and exit Bios Setup Configuring RAID array in RAID Bios Create Array StepsJraid RDD0 Jraid Status MembersHDDx Delete Array Making a Sata Driver Disk Required for Ahci and RAID Mode Cd bootdrv MenuWindows Setup ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English English English Contact Us Taiwan HeadquartersGigabyte Global Service System
Top Page Image Contents