Gigabyte GA-8I915P DUO user manual Feature Summary, Cpu

Page 10

English

1-2 Feature Summary

CPU

Š

Supports the latest Intel® Pentium® 4 LGA775 CPU

 

Š

Supports 800/533MHz FSB

 

Š L2 cache varies with CPU

Chipset

Š

Northbridge: Intel® 915P Express Chipset

 

Š

Southbridge: Intel® ICH6

 

Š Supported on the Win 2000/XP operating systems

Memory

Š

2 DDR DIMM memory slots (supports up to 2GB memory)

 

Š Supports 2.5V DDR DIMM

 

Š Supports dual channel DDR 400/333 DIMM

 

Š 2 DDR II DIMM memory slots (supports up to 2GB memory)

 

Š Supports 1.8V DDR II DIMM

 

Š Supports dual channel DDR II 600(Note)/533/400 DIMM

 

 

(Note: Mixed mode, populating DDR and DDR II memory modules

 

 

simultaneously is not supported.)

Slots

Š

1 PCI Express x 16 slot

 

Š 2 PCI Express x 1 slots

 

Š

3 PCI slots

IDE Connections

Š

1 IDE connection (UDMA 33/ATA 66/ATA 100), allows connection of 2

 

 

IDE devices(IDE1)

 

 

- Supported on the Win 2000/XP operating systems

 

Š 2 IDE connection (UDMA 33/ATA 66/ATA 100/ATA 133), compatible with

 

 

RAID, allows connection of 4 IDE devices(IDE2,IDE3)

FDD Connections

Š

1 FDD connection, allows connection of 2 FDD devices

Onboard SATA

Š

4 Serial ATA connections

 

Š Supported on the Win 2000/XP operating systems

Peripherals

Š

1 parallel port supporting Normal/EPP/ECP mode

 

Š 2 Serial port (COMA/COMB)

 

Š 8 USB 2.0/1.1 ports (rear x 4, front x 4 via cable)

 

Š 1 front audio connector

 

Š

1 IR connector

 

Š 1 PS/2 keyboard port

 

Š 1 PS/2 mouse port

Onboard LAN

Š

Onboard Marvell 8001 chip (10/100/1000 Mbit)

Š 1 RJ 45 port

(Note) To use a DDRII 600 memory module on the motherboard, you must install an 800MHz FSB processor and overclock in BIOS.

GA-8I915P Duo Motherboard

- 10 -

Image 10
Contents GA-8I915P Duo Motherboard Copyright Product Manual ClassificationTable of Contents Install Drivers GA-8I915P Duo Motherboard Layout 8I915PDuo Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary CPUALC850 Codec UAJ Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel DDR/DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE1/IDE2/IDE3 IDE Connector SATA0/SATA1/SATA2/SATA3 Serial ATA ConnectorFpanel Front Panel Jumper Faudio Front Audio Connector PwrledCdin CD Spdifio Spdif In/OutUSB1 / FUSB2 Front USB Connector 14 IRCI Chassis Intrusion, Case Open Clrcmos Clear CmosBATBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E1 Standard Cmos Features IDE Channel 2/3 Master, Slave Floppy 3 Mode Support for Japan AreaIDE Channel 0 Master, Slave Drive a / Drive BBase Memory Halt onMemory Extended MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Limit Cpuid Max. to Password CheckCPU Hyper-Threading No-Execute Memory ProtectNoteIntegrated Peripherals On-Chip Primary PCI IDESata Port 0/2 Set to On-Chip Sata ModePata IDE Set to Sata Port 1/3 Set toUR2 Duplex Mode Onboard LAN Boot ROMUart Mode Select Parallel Port ModeResume by Alarm Power Management SetupPower On By Mouse KB Power on Password Power On By KeyboardAC Back Function PnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status CPU Smart FAN Control CPU Smart FAN ModeMB Intelligent TweakerM.I.T CPU Clock RatioCPU Host Clock Control Robust Graphics BoosterA.2 CPU Host Frequency MhzPCI-E OverVoltage Control Memory Frequency MhzDimm OverVoltage Control FSB OverVoltage ControlLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingInstall Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewWhat is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery F9 For Xpress Recovery EnglishRemove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartMethod 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to 4 to flash the backup BIOS, too Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Stereo Speakers Connection and Settings Introduction of audio connectors4 2- / 4- / 6- / 8- ChannelAudio Function Introduction Channel Audio Setup English Step Jack-Sensing and UAJ Introduction English Troubleshooting AMI Bios Beep CodesEnglish English English English English Contact Us Taiwan HeadquartersChina Shanghai