Gigabyte GA-8I915P DUO user manual ALC850 Codec UAJ

Page 11

Onboard Audio		ALC850 CODEC (UAJ)
	Supports Jack Sensing function
	Supports 2 / 4 / 6 / 8 channel audio
	Supports Line In ; Line Out (Front Speaker Out) ; MIC ; Surround Speaker Out
		(Rear Speaker Out) ; Center/Subwoofer Speaker Out ;
		Side Speaker Out connection
	Supports SPDIF In/Out connection
		CD In
On-Board IDE RAID		Built-in VT6410 chipset
(IDE2, IDE3)		Supports disk striping (RAID 0) or disk mirroring (RAID 1) or
		striping + mirroring (RAID 0 + RAID 1)
		supports JBOD function
	Supports concurrent dual ATA133 IDE controller operation
	Supports IDE bus master operation
	Support ATAPI mode for HDD
	Displays status and error checking messages during boot-up
	Mirroring supports automatic background rebuilds
	Features LBA and Extended Interrupt 13 drive translation in
		controller onboard BIOS

I/O Control		IT8712
Hardware Monitor		System voltage detection
		CPU temperature detection
	CPU / System fan speed detection
		CPU warning temperature
	CPU / System fan failure warning
	CPU smart fan control
BIOS		Use of licensed AWARD BIOS
		Supports Q-Flash
Additional Features		Supports @BIOS
		Supports EasyTune 5

Overclocking		Over Voltage via BIOS (CPU/DDR/PCIE/FSB)
	Over Clock via BIOS (CPU/DDR/PCIE)
Form Factor		ATX form factor; 30.5cm x 22.0cm

English

- 11 -

Hardware Installation

Image 11

Contents GA-8I915P Duo Motherboard Product Manual Classification CopyrightTable of Contents Install Drivers 8I915PDuo GA-8I915P Duo Motherboard LayoutBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryALC850 Codec UAJ Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel DDR/DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD Floppy Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0/SATA1/SATA2/SATA3 Serial ATA Connector IDE1/IDE2/IDE3 IDE ConnectorFpanel Front Panel Jumper Pwrled Faudio Front Audio ConnectorSpdifio Spdif In/Out Cdin CD14 IR USB1 / FUSB2 Front USB ConnectorClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBATBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E1 Standard Cmos Features Drive a / Drive B Floppy 3 Mode Support for Japan AreaIDE Channel 0 Master, Slave IDE Channel 2/3 Master, SlaveExtended Memory Halt onMemory Base MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority No-Execute Memory ProtectNote Password CheckCPU Hyper-Threading Limit Cpuid Max. toOn-Chip Primary PCI IDE Integrated PeripheralsSata Port 1/3 Set to On-Chip Sata ModePata IDE Set to Sata Port 0/2 Set toParallel Port Mode Onboard LAN Boot ROMUart Mode Select UR2 Duplex ModePower On By Mouse Power Management SetupResume by Alarm AC Back Function Power On By KeyboardKB Power on Password PCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status CPU Clock Ratio CPU Smart FAN ModeMB Intelligent TweakerM.I.T CPU Smart FAN ControlCPU Host Frequency Mhz Robust Graphics BoosterA.2 CPU Host Clock ControlFSB OverVoltage Control Memory Frequency MhzDimm OverVoltage Control PCI-E OverVoltage ControlLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Install DriversDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionHow to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? English F9 For Xpress RecoveryExit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish 4 2- / 4- / 6- / 8- ChannelAudio Function Introduction Introduction of audio connectorsStereo Speakers Connection and Settings Channel Audio Setup English Step Jack-Sensing and UAJ Introduction English AMI Bios Beep Codes TroubleshootingEnglish English English English English Taiwan Headquarters Contact UsChina Shanghai