Gigabyte GA-8I915P DUO user manual Jack-Sensing and UAJ Introduction

Page 71

4-1-5 Jack-Sensing and UAJ Introduction

Jack-Sensing provides audio connectors error-detection function.

Install Microsoft DirectX8.1 or later version before to enable Jack-Sensing support for Windows 98/98SE/2000/ME.

Jack-Sensing includes 2 parts: AUTO and MANUAL. Following is an example for 2 channels (Windows XP):

Introduction of audio connectors

You may connect CDROM, Walkman or others audio input devices to Line In jack, speakers, earphone or others output devices to Line Out jack, and micro- phone to MIC In jack.

Auto-detecting:

Please connect the devices to the right jacks as above. A window will appear as right

picture if you setup the devices properly. Please note that 3D audio function will only appear when 3D audio inputs.

English

- 71 -

Appendix

Image 71

Contents GA-8I915P Duo Motherboard Product Manual Classification CopyrightTable of Contents Install Drivers 8I915PDuo GA-8I915P Duo Motherboard LayoutBlock Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyCPU Feature SummaryALC850 Codec UAJ Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Installation of Memory Dual Channel DDR/DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector FDD Floppy Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATA0/SATA1/SATA2/SATA3 Serial ATA Connector IDE1/IDE2/IDE3 IDE ConnectorFpanel Front Panel Jumper Pwrled Faudio Front Audio ConnectorSpdifio Spdif In/Out Cdin CD14 IR USB1 / FUSB2 Front USB ConnectorClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBATBattery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E1 Standard Cmos Features Drive a / Drive B Floppy 3 Mode Support for Japan AreaIDE Channel 0 Master, Slave IDE Channel 2/3 Master, SlaveExtended Memory Halt onMemory Base MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority No-Execute Memory ProtectNote Password CheckCPU Hyper-Threading Limit Cpuid Max. toOn-Chip Primary PCI IDE Integrated PeripheralsSata Port 1/3 Set to On-Chip Sata ModePata IDE Set to Sata Port 0/2 Set toParallel Port Mode Onboard LAN Boot ROMUart Mode Select UR2 Duplex ModePower On By Mouse Power Management SetupResume by Alarm AC Back Function Power On By KeyboardKB Power on Password PCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status CPU Clock Ratio CPU Smart FAN ModeMB Intelligent TweakerM.I.T CPU Smart FAN ControlCPU Host Frequency Mhz Robust Graphics BoosterA.2 CPU Host Clock ControlFSB OverVoltage Control Memory Frequency MhzDimm OverVoltage Control PCI-E OverVoltage ControlLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Install DriversDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities User Interface Overview EasyTune 5 IntroductionHow to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? English F9 For Xpress RecoveryExit and Restart Remove Backup Image Remove backup image. Are you sure? Y/NBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish 4 2- / 4- / 6- / 8- ChannelAudio Function Introduction Introduction of audio connectorsStereo Speakers Connection and Settings Channel Audio Setup English Step Jack-Sensing and UAJ Introduction English AMI Bios Beep Codes TroubleshootingEnglish English English English English Taiwan Headquarters Contact UsChina Shanghai