Gigabyte Explore the Features and Connections of the 8I915P Duo Motherboard
Page 20

English

3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector)

The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin (only for CPU_FAN) power connector and possesses a foolproof connection design.

Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND).

Please remember to connect the power to the cooler to prevent system overheating and failure. Caution!

Please remember to connect the power to the CPU fan to prevent CPU overheating and failure.

1

 

 

 

 

 

Pin No.

Definition

 

 

 

 

 

 

1

GND

 

 

 

 

 

 

CPU_FAN

2

+12V

 

 

 

 

 

 

3

Sense

 

 

 

 

 

 

4

Speed Control

 

 

 

 

1

 

(Only for CPU_FAN)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SYS_FAN

 

 

5)FDD (Floppy Connector)

The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB. Please connect the red power connector wire to the pin1 position.

34 33

2

1

GA-8I915P Duo Motherboard

- 20 -

Page 19 Page 21
Image 20
Page 19 Page 21
Contents GA-8I915P Duo Motherboard Copyright Product Manual ClassificationTable of Contents Install Drivers GA-8I915P Duo Motherboard Layout 8I915PDuoBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUALC850 Codec UAJ Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel DDR/DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE1/IDE2/IDE3 IDE Connector SATA0/SATA1/SATA2/SATA3 Serial ATA ConnectorFpanel Front Panel Jumper Faudio Front Audio Connector PwrledCdin CD Spdifio Spdif In/OutUSB1 / FUSB2 Front USB Connector 14 IRCI Chassis Intrusion, Case Open Clrcmos Clear CmosBATBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E1 Standard Cmos Features Floppy 3 Mode Support for Japan Area IDE Channel 0 Master, SlaveIDE Channel 2/3 Master, Slave Drive a / Drive BHalt on MemoryBase Memory Extended MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Password Check CPU Hyper-ThreadingLimit Cpuid Max. to No-Execute Memory ProtectNoteIntegrated Peripherals On-Chip Primary PCI IDEOn-Chip Sata Mode Pata IDE Set toSata Port 0/2 Set to Sata Port 1/3 Set toOnboard LAN Boot ROM Uart Mode SelectUR2 Duplex Mode Parallel Port ModePower On By Mouse Power Management SetupResume by Alarm AC Back Function Power On By KeyboardKB Power on Password PnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status CPU Smart FAN Mode MB Intelligent TweakerM.I.TCPU Smart FAN Control CPU Clock RatioRobust Graphics Booster A.2CPU Host Clock Control CPU Host Frequency MhzMemory Frequency Mhz Dimm OverVoltage ControlPCI-E OverVoltage Control FSB OverVoltage ControlLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingInstall Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewHow to use the Xpress Recovery Xpress Recovery IntroductionWhat is Xpress Recovery ? F9 For Xpress Recovery EnglishRemove Backup Image  Remove backup image. Are you sure? Y/N Exit and RestartBefore You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to 4 to flash the backup BIOS, too Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish 4 2- / 4- / 6- / 8- ChannelAudio Function Introduction Introduction of audio connectorsStereo Speakers Connection and Settings Channel Audio Setup English Step Jack-Sensing and UAJ Introduction English Troubleshooting AMI Bios Beep CodesEnglish English English English English Contact Us Taiwan HeadquartersChina Shanghai
Top Page Image Contents