Gigabyte GA-8I915P DUO user manual Integrated Peripherals, On-Chip Primary PCI IDE

Page 36

English

2-3	Integrated Peripherals

		CMOS Setup Utility-Copyright (C) 1984-2004 Award Software
			Integrated Peripherals
	On-Chip Primary PCI IDE		[Enabled]					Item Help
	On-Chip SATA Mode		[Auto]					Menu Level`
x	PATA IDE Set to		Ch.0 Master/Slave
	SATA Port 0/2 Set to		Ch.2 Master/Slave
	SATA Port 1/3 Set to		Ch.3 Master/Slave
	USB Controller		[Enabled]
	USB 2.0 Controller		[Enabled]
	USB Keyboard Support		[Disabled]
	USB Mouse Support		[Disabled]
	AC97 Audio		[Auto]
	Onboard H/W RAID		[Enabled]
	Onboard H/W LAN		[Enabled]
	Onboard LAN Boot ROM		[Disabled]
	Onboard Serial Port 1		[3F8/IRQ4]
	Onboard Serial Port 2		[2F8/IRQ3]
	UART Mode Select		[Normal]
x	UR2 Duplex Mode		Half
	Onboard Parallel Port		[378/IRQ7]
	Parallel Port Mode		[SPP]
KLJI: Move		Enter: Select	+/-/PU/PD: Value	F10: Save	ESC: Exit				F1: General Help
	F5: Previous Values		F6: Fail-Safe Defaults		F7: Optimized Defaults

		CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
			Integrated Peripherals
x ECP Mode Use DMA			3					Item Help
								Menu Level`

KLJI: Move	Enter: Select	+/-/PU/PD: Value	F10: Save	ESC: Exit	F1: General Help
F5: Previous Values		F6: Fail-Safe Defaults		F7: Optimized Defaults

On-Chip Primary PCI IDE

Enabled	Enable onboard 1st channel IDE port. (Default value)
Disabled	Disable onboard 1st channel IDE port.

GA-8I915P Duo Motherboard

- 36 -

Image 36

Contents GA-8I915P Duo Motherboard Copyright Product Manual ClassificationTable of Contents Install Drivers GA-8I915P Duo Motherboard Layout 8I915PDuoBlock Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary CPUALC850 Codec UAJ Installation of the CPU and Heatsink Installation of the CPUInstallation of the Heatsink Installation of Memory Dual Channel DDR/DDR Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD Floppy ConnectorIDE1/IDE2/IDE3 IDE Connector SATA0/SATA1/SATA2/SATA3 Serial ATA ConnectorFpanel Front Panel Jumper Faudio Front Audio Connector PwrledCdin CD Spdifio Spdif In/OutUSB1 / FUSB2 Front USB Connector 14 IRCI Chassis Intrusion, Case Open Clrcmos Clear CmosBATBattery English Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. E1 Standard Cmos Features Floppy 3 Mode Support for Japan Area IDE Channel 0 Master, SlaveIDE Channel 2/3 Master, Slave Drive a / Drive B Halt on Memory Base Memory Extended MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Password Check CPU Hyper-ThreadingLimit Cpuid Max. to No-Execute Memory ProtectNoteIntegrated Peripherals On-Chip Primary PCI IDEOn-Chip Sata Mode Pata IDE Set toSata Port 0/2 Set to Sata Port 1/3 Set toOnboard LAN Boot ROM Uart Mode SelectUR2 Duplex Mode Parallel Port ModePower Management Setup Resume by AlarmPower On By Mouse Power On By Keyboard KB Power on PasswordAC Back Function PnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status CPU Smart FAN Mode MB Intelligent TweakerM.I.TCPU Smart FAN Control CPU Clock RatioRobust Graphics Booster A.2CPU Host Clock Control CPU Host Frequency MhzMemory Frequency Mhz Dimm OverVoltage ControlPCI-E OverVoltage Control FSB OverVoltage ControlLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingInstall Drivers Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewXpress Recovery Introduction What is Xpress Recovery ?How to use the Xpress Recovery F9 For Xpress Recovery EnglishRemove Backup Image Remove backup image. Are you sure? Y/N Exit and RestartFlash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to 4 to flash the backup BIOS, too Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Introduction of audio connectors Stereo Speakers Connection and Settings4 2- / 4- / 6- / 8- ChannelAudio Function Introduction Channel Audio Setup English Step Jack-Sensing and UAJ Introduction English Troubleshooting AMI Bios Beep CodesEnglish English English English English Contact Us Taiwan HeadquartersChina Shanghai