Gigabyte 8S648FX-RZ-C user manual FUSB1 / FUSB2 Front USB Connector, Clrcmos Clear Cmos

Page 18

English

14) F_USB1 / F_USB2 (Front USB Connector)

Be careful with the polarity of the front USB connector. Check the pin assignment carefully while you connect the front USB cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional front USB cable, please contact your local dealer.

 

 

Pin No.

Definition

 

 

1

Power

 

 

2

Power

2

10

3

USB DX-

4

USB Dy-

 

 

5

USB DX+

1

9

6

USB Dy+

 

 

7

GND

 

 

8

GND

-C

 

9

No Pin

 

 

10

NC

15) CLR_CMOS (Clear CMOS)

You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily shor 1-2 pin. Default doesn't include the "Shunter" to prevent from improper use this jumper.

1 Open: Normal

1

Short: Clear CMOS

 

-C

16) BAT (BATTERY)

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.

+ Dispose of used batteries according to the manufacturer's instructions.

 

If you want to erase CMOS...

 

1. Turn OFF the computer and unplug the power cord.

 

2. Remove the battery, wait for 30 second.

-C

3. Re-install the battery.

 

4. Plug the power cord and turn ON the computer.

8S648FX-RZ Series Motherboard

- 18 -

Image 18
Contents 8S648FX-RZ / 8S648FX-RZ-C Motherboard 8S648FX-RZ Installing the motherboard to the chassis Preparing Your ComputerTable of Contents Features Summary IntroductionVRM10.0 8S648FX-RZ Series Motherboard Layout8S648FX-RZ P4 TitanBlock Diagram EnglishHardware Installation Process Install the Central Processing Unit CPUStep CPU Installation Install Memory Modules Install AGP Card Install I/O Peripherals CablesFUSB1 / FUSB2 CdinAuxin 16 BATATX12V +12V Power Connector ATX ATX PowerCpufan CPU Fan Connector Sysfan System Fan Connector IDE1 / IDE2 IDE1 / IDE2 ConnectorFDD Floppy Connector Fpanel 2 x 10 pins Connector PwrledFaudio Front Audio Connector Surcen Surround Center ConnectorCdin CD In Connector Auxin AUX In Connector Spdifio Spdif In/Out ConnectorFUSB1 / FUSB2 Front USB Connector Clrcmos Clear CmosMain Menu For example Bios Ver. F7d Status Page Setup Menu / Option Page Setup MenuMain Menu PnP/PCI Configuration Advanced Bios FeaturesPower Management Setup Load Fail-Safe DefaultsTime Standard Cmos FeaturesDate IDE Primary Master, Slave / IDE Secondary Master, SlaveHalt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryBoot Up Floppy Seek Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckIntegrated Peripherals AC97 Audio Parallel Port ModeECP Mode Use DMA On Board LAN devicePower Management Setup Resume by Alarm Power On by KeyboardPower On by Mouse IRQ 3-7, 9-15, NMIPCI 1/PCI 5 IRQ Assignment PnP/PCI ConfigurationsPCI 4 IRQ Assignment PCI 2 IRQ AssignmentCurrent Voltage V Vcore / DDR25V / +3.3V / +12V Current CPU TemperaturePC Health Status Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control PCI Clock MHz Top PerformanceAGP Clock MHz AGP Voltage ControlLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password ConfigurationsEnter PasswordSave & Exit Setup Exit Without SavingInstall Drivers Pictures below are shown in Windows XPItem Description Memo English English Contact US