Gigabyte 8S648FX-RZ AC97 Audio, On Board LAN device, USB Controller, USB Legacy Support

Page 25

AC97 Audio

Enabled

Enable onboard AC'97 audio function. (Default value)

Disabled

Disable this function.

On Board LAN device *

Disabled

Disable this function.

Enabled

Enable Onboard Lan Chip device. (Default value)

USB Controller

 

Enabled

Enable USB Controller. (Default value)

Disabled

Disable USB Controller.

USB Legacy Support

When USB keyboard or mouse is installed, please set at Enabled.

Enabled

Enable USB keyboard or mouse support.

Disabled

Disable USB keyboard or mouse support. (Default value)

Onboard Serial Port 1

Auto

BIOS will automatically setup the port 1 address.

3F8/IRQ4

Enable onboard Serial port 1 and address is 3F8. (Default value)

2F8/IRQ3

Enable onboard Serial port 1 and address is 2F8.

3E8/IRQ4

Enable onboard Serial port 1 and address is 3E8.

2E8/IRQ3

Enable onboard Serial port 1 and address is 2E8.

Disabled

Disable onboard Serial port 1.

Onboard Serial Port 2

Auto

BIOS will automatically setup the port 2 address.

3F8/IRQ4

Enable onboard Serial port 2 and address is 3F8.

2F8/IRQ3

Enable onboard Serial port 2 and address is 2F8. (Default value)

3E8/IRQ4

Enable onboard Serial port 2 and address is 3E8.

2E8/IRQ3

Enable onboard Serial port 2 and address is 2E8.

Disabled

Disable onboard Serial port 2.

Onboard Parallel port

378/IRQ7

Enable onboard LPT port and address is 378/IRQ7. (Default value)

278/IRQ5

Enable onboard LPT port and address is 278/IRQ5.

Disabled

Disable onboard LPT port.

3BC/IRQ7

Enable onboard LPT port and address is 3BC/IRQ7.

Parallel Port Mode

SPP

Using Parallel port as Standard Parallel Port. (Default value)

EPP

Using Parallel port as Enhanced Parallel Port.

ECP

Using Parallel port as Extended Capabilities Port.

ECP+EPP

Using Parallel port as ECP & EPP mode.

ECP Mode Use DMA

3

Set ECP Mode Use DMA to 3. (Default value)

1

Set ECP Mode Use DMA to 1.

"*" Only for 8S648FX-RZ.

English

- 25 -

BIOS Setup

Image 25
Contents 8S648FX-RZ / 8S648FX-RZ-C Motherboard 8S648FX-RZ Preparing Your Computer Installing the motherboard to the chassisTable of Contents Introduction Features Summary8S648FX-RZ 8S648FX-RZ Series Motherboard LayoutVRM10.0 P4 TitanEnglish Block DiagramInstall the Central Processing Unit CPU Hardware Installation ProcessStep CPU Installation Install Memory Modules Install I/O Peripherals Cables Install AGP CardAuxin CdinFUSB1 / FUSB2 16 BATATX ATX Power ATX12V +12V Power ConnectorCpufan CPU Fan Connector IDE1 / IDE2 IDE1 / IDE2 Connector Sysfan System Fan ConnectorFDD Floppy Connector Pwrled Fpanel 2 x 10 pins ConnectorSurcen Surround Center Connector Faudio Front Audio ConnectorCdin CD In Connector Spdifio Spdif In/Out Connector Auxin AUX In ConnectorClrcmos Clear Cmos FUSB1 / FUSB2 Front USB ConnectorStatus Page Setup Menu / Option Page Setup Menu Main Menu For example Bios Ver. F7dMain Menu Power Management Setup Advanced Bios FeaturesPnP/PCI Configuration Load Fail-Safe DefaultsDate Standard Cmos FeaturesTime IDE Primary Master, Slave / IDE Secondary Master, SlaveDrive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesBoot Up Floppy Seek Password CheckIntegrated Peripherals ECP Mode Use DMA Parallel Port ModeAC97 Audio On Board LAN devicePower Management Setup Power On by Mouse Power On by KeyboardResume by Alarm IRQ 3-7, 9-15, NMIPCI 4 IRQ Assignment PnP/PCI ConfigurationsPCI 1/PCI 5 IRQ Assignment PCI 2 IRQ AssignmentPC Health Status Current CPU TemperatureCurrent Voltage V Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control AGP Clock MHz Top PerformancePCI Clock MHz AGP Voltage ControlLoad Optimized Defaults Load Fail-Safe DefaultsConfigurationsEnter Password Set Supervisor/User PasswordExit Without Saving Save & Exit SetupPictures below are shown in Windows XP Install DriversItem Description Memo English English Contact US