Gigabyte 8S648FX-RZ-C Hardware Installation Process, Install the Central Processing Unit CPU

Page 8

English

Hardware Installation Process

To set up your computer, you must complete the following steps:

Step 1- Install the Central Processing Unit (CPU)

Step 2- Install memory modules

Step 3- Install expansion cards

Step 4- Install I/O Peripherals Cables

Step 4 Step 1 Step 2

Step 4

Step 4

Step 3

C-

Step 1: Install the Central Processing Unit (CPU)

Before installing the processor, adhere to the following warning:

1.Please make sure the CPU type is supported by the motherboard.

2.The processor will overheat without the heatsink and/or fan, resulting in permanent irreparable damage.

3.If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause improper installation. Please change the insert orientation.

4.Apply thermal grease between the processor and cooling fan.

5.Never run the processor without the heatsink properly and firmly attached. Permanent damage will result.

6.Please set the CPU host frequency in accordance with your processor's specifications. We don't recommend you to set the system bus frequency over the CPU's specification because these specific bus frequencies are not the standard specifications for CPU, chipset and most of the peripherals. Whether your system can run under these specific bus frequencies properly will depend on your hardware configurations, including CPU, Memory, Cards…etc.

HT functionality requirement content :

Enabling the functionality of Hyper-Threading Technology for your computer system requires all of the following platform components:

-CPU: An Intel® Pentium 4 Processor with HT Technology

-Chipset: An SiS® Chipset that supports HT Technology

-BIOS: A BIOS that supports HT Technology and has it enabled

-OS: An operation system that has optimizations for HT Technology

8S648FX-RZ Series Motherboard

- 8 -

Image 8
Contents 8S648FX-RZ / 8S648FX-RZ-C Motherboard 8S648FX-RZ Installing the motherboard to the chassis Preparing Your ComputerTable of Contents Features Summary Introduction8S648FX-RZ Series Motherboard Layout 8S648FX-RZVRM10.0 P4 TitanBlock Diagram EnglishStep Hardware Installation ProcessInstall the Central Processing Unit CPU CPU Installation Install Memory Modules Install AGP Card Install I/O Peripherals CablesCdin AuxinFUSB1 / FUSB2 16 BATCpufan CPU Fan Connector ATX12V +12V Power ConnectorATX ATX Power FDD Floppy Connector Sysfan System Fan ConnectorIDE1 / IDE2 IDE1 / IDE2 Connector Fpanel 2 x 10 pins Connector PwrledCdin CD In Connector Faudio Front Audio ConnectorSurcen Surround Center Connector Auxin AUX In Connector Spdifio Spdif In/Out ConnectorFUSB1 / FUSB2 Front USB Connector Clrcmos Clear CmosMain Menu Main Menu For example Bios Ver. F7dStatus Page Setup Menu / Option Page Setup Menu Advanced Bios Features Power Management SetupPnP/PCI Configuration Load Fail-Safe DefaultsStandard Cmos Features DateTime IDE Primary Master, Slave / IDE Secondary Master, SlaveFloppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryAdvanced Bios Features First / Second / Third Boot DeviceBoot Up Floppy Seek Password CheckIntegrated Peripherals Parallel Port Mode ECP Mode Use DMAAC97 Audio On Board LAN devicePower Management Setup Power On by Keyboard Power On by MouseResume by Alarm IRQ 3-7, 9-15, NMIPnP/PCI Configurations PCI 4 IRQ AssignmentPCI 1/PCI 5 IRQ Assignment PCI 2 IRQ AssignmentCurrent CPU Temperature PC Health StatusCurrent Voltage V Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control Top Performance AGP Clock MHzPCI Clock MHz AGP Voltage ControlLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password ConfigurationsEnter PasswordSave & Exit Setup Exit Without SavingInstall Drivers Pictures below are shown in Windows XPItem Description Memo English English Contact US