Gigabyte 8S648FX-RZ-C user manual Set Supervisor/User Password, ConfigurationsEnter Password

Page 33

Set Supervisor/User Password

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

`

Standard CMOS Features

 

 

Top Performance

 

`

Advanced BIOS Features

 

 

Load Fail-Safe Defaults

 

`

Integrated Peripherals

 

 

Load Optimized Defaults

 

`

 

 

 

 

 

 

Power

Management Setup

 

 

Set Supervisor Password

 

 

 

`

PnP/PCI

ConfigurationsEnter Password:

Set User Password

 

`

PC Health

Status

 

 

Save & Exit Setup

 

`

Frequency/Voltage Control

 

 

Exit Without Saving

 

 

 

 

 

 

 

 

ESC: Quit

KLJI: Select Item

F8: Q-Flash

F10: Save & Exit Setup

 

 

 

Change/Set/Disable Password

When you select this function, the following message will appear at the center of the screen to assist you in creating a password.

Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a password.

To disable password, just press <Enter> when you are prompted to enter password. A message "PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is disabled, the system will boot and you can enter Setup freely.

The BIOS Setup program allows you to specify two separate passwords:

SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOS Setup program function. When enabled, the Supervisor password is required for entering the BIOS Setup program and having full configuration fields, the User password is required to access only basic items.

If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be prompted for the password every time the system is rebooted or any time you try to enter Setup Menu.

If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted only when you try to enter Setup.

English

- 33 -

BIOS Setup

Image 33
Contents 8S648FX-RZ / 8S648FX-RZ-C Motherboard 8S648FX-RZ Preparing Your Computer Installing the motherboard to the chassisTable of Contents Introduction Features Summary8S648FX-RZ 8S648FX-RZ Series Motherboard LayoutVRM10.0 P4 TitanEnglish Block DiagramHardware Installation Process Install the Central Processing Unit CPUStep CPU Installation Install Memory Modules Install I/O Peripherals Cables Install AGP CardAuxin CdinFUSB1 / FUSB2 16 BATATX12V +12V Power Connector ATX ATX PowerCpufan CPU Fan Connector Sysfan System Fan Connector IDE1 / IDE2 IDE1 / IDE2 ConnectorFDD Floppy Connector Pwrled Fpanel 2 x 10 pins ConnectorFaudio Front Audio Connector Surcen Surround Center ConnectorCdin CD In Connector Spdifio Spdif In/Out Connector Auxin AUX In ConnectorClrcmos Clear Cmos FUSB1 / FUSB2 Front USB ConnectorMain Menu For example Bios Ver. F7d Status Page Setup Menu / Option Page Setup MenuMain Menu Power Management Setup Advanced Bios FeaturesPnP/PCI Configuration Load Fail-Safe DefaultsDate Standard Cmos FeaturesTime IDE Primary Master, Slave / IDE Secondary Master, SlaveDrive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesBoot Up Floppy Seek Password CheckIntegrated Peripherals ECP Mode Use DMA Parallel Port ModeAC97 Audio On Board LAN devicePower Management Setup Power On by Mouse Power On by KeyboardResume by Alarm IRQ 3-7, 9-15, NMIPCI 4 IRQ Assignment PnP/PCI ConfigurationsPCI 1/PCI 5 IRQ Assignment PCI 2 IRQ AssignmentPC Health Status Current CPU TemperatureCurrent Voltage V Vcore / DDR25V / +3.3V / +12V Current CPU/SYSTEM FAN Speed RPMFrequency/Voltage Control AGP Clock MHz Top PerformancePCI Clock MHz AGP Voltage ControlLoad Optimized Defaults Load Fail-Safe DefaultsConfigurationsEnter Password Set Supervisor/User PasswordExit Without Saving Save & Exit SetupPictures below are shown in Windows XP Install DriversItem Description Memo English English Contact US