Gigabyte Understanding the F_USB3 Front USB Connector for Optimal Device Connection

Page 29

16)F_ USB1 / F_USB2 / F_USB3 (Front USB Connector)

Be careful with the polarity of the front USB connector. Check the pin assignment carefully while you connect the front USB cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional front USB cable, please contact your local dealer.

 

 

Pin No.

Definition

1 0

9

1

Power (5V)

2

Power (5V)

 

 

 

 

3

USB DX-

 

 

4

USB Dy-

2

1

5

USB DX+

 

 

6

USB Dy+

 

 

7

GND

 

 

8

GND

 

 

9

No Pin

 

 

10

NC

English

17)F1_1394 / F2_1394 (Front IEEE 1394 Connector)

Serial interface standard set by Institute of Electrical and Electronics Engineers, which has features like high speed, highbandwidth and hot plug. Be careful with the polarity of the IEEE1394 connector. Check the pin assignment carefully while you connect the IEEE1394 cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional IEEE1394 cable, please contact your local dealer.

 

 

Pin No.

Definition

2

1 0

1

TPA+

1

9

2

TPA-

3

GND

 

 

 

 

4

GND

 

 

5

TPB+

 

 

6

TPB-

 

 

7

Power (12V)

 

 

8

Power (12V)

 

 

9

No Pin

 

 

10

GND

- 29 -

Hardware Installation

Image 29
Contents GA-M57SLI-S4 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-M57SLI-S4 Motherboard Layout Block Diagram Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerFeature Summary 4Mbit flash ROM Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Before you begin Setup of SLI Scalable Link Interface ConfigurationConnecting Two Graphics Cards Graphics Card Driver Setting I/O Back Panel Introduction Line Connectors IntroductionLine Out Front Speaker Out MICATX12V / ATX Power Connector 6 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector PCIE12V Power ConnectorIDE1 IDE Connector FDD FDD ConnectorEnglish Fpanel Front Panel Jumper Pwrled Faudio Front Audio ConnectorSpdifi Spdif In Connector Cdin CD In Connector17 F11394 / F21394 Front Ieee 1394 Connector USB1 / FUSB2 / FUSB3 Front USB ConnectorClrcmos Clear Cmos CI Chassis Intrusion, Case OpenMain Menu Status Page Setup Menu / Option Page Setup MenuBios Setting Recovery Main Menu For example Bios Ver. F3cF12 Boot Menu „ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 2/3/4/5/6/7 Master TimeIDE Channel 0 Master/Slave Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryBoot Up Floppy Seek Hard Disk Boot PriorityFirst / Second / Third Boot Device Init Display First Password CheckAway Mode NV Sata 1 Primary RAID NV Sata RAID functionNV Sata 1 Secondary RAID NV Sata 2 Primary RAIDNV Sata 2 Secondary RAID IDE Prefetch ModeNV Sata 3 Primary RAID NV Sata 3 Secondary RAIDParallel Port Mode Onboard LAN Boot ROMOnboard Onboard Serial PortOn-Chip USB ECP Mode Use DMAUSB Keyboard Support USB Mouse SupportPME Event Wake Up Power-On by AlarmModem Ring On USB Resume from SuspendPower On By Keyboard Power On By MouseKB Power on Password AC Back FunctionPCI 1 IRQ Assignment PnP/PCI ConfigurationsPCI 2 IRQ Assignment Current CPU/POWER/SYSTEM FAN Speed RPM Current CPU TemperatureCPU Warning Temperature Case OpenedCPU Smart FAN Control Note CPU Smart FAN ModePcie Clock MHz CPU Frequency MHzCPU Clock Ratio Robust Graphics BoosterCPU HT-Link Voltage HT-Link VoltageCPU Voltage Control Normal CPU VcoreLoad Fail-Safe Defaults Set Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Press Y on your keyboard to save and exit FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Installing Sata hard drives in your computer Smart LAN Nvidia Mirror Step Save and exit Bios Setup GA-M57SLI-S4 Motherboard Configuring RAID set in RAID Bios YES Nvidia Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Solutions Configuring a bootable RAID array with Microsoft WindowsYES GA-M57SLI-S4 Motherboard 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English English English English English Taiwan Headquarters Contact UsGigabyte Global Service System