Gigabyte GA-M57SLI-S4 user manual CPU Smart FAN Control Note, CPU Smart FAN Mode

Page 46

English

CPU Smart FAN Control (Note)

Disabled	Disable this function.
Enabled	When this function is enabled, CPU fan will run at different speed depending on
	CPU temperature. Users can adjust the fan speed with Easy Tune based on
	their requirements. (Default value)

CPU Smart FAN Mode

This option is available only when CPU Smart FAN Control is enabled.

Auto	BIOS autodetects the type of CPU fan you installed and sets the optimal CPU
	Smart FAN control mode for it. (Default Value)
Voltage	Set to Voltage when you use a CPU fan with a 3-pin fan power cable.
PWM	Set to PWM when you use a CPU fan with a 4-pin fan power cable.

(Note) Whether the CPU Smart FAN Control function is supported will depend on the CPU you install.

GA-M57SLI-S4 Motherboard

- 46 -

Image 46

Contents GA-M57SLI-S4 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-M57SLI-S4 Motherboard Layout Block Diagram Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary 4Mbit flash ROM Installation of the CPU and CPU Cooler Installation of the CPUInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Setup of SLI Scalable Link Interface Configuration Before you beginConnecting Two Graphics Cards Graphics Card Driver Setting I/O Back Panel Introduction Line Out Front Speaker Out Connectors IntroductionLine MICATX12V / ATX Power Connector PCIE12V Power Connector 6 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorFDD FDD Connector IDE1 IDE ConnectorEnglish Fpanel Front Panel Jumper Faudio Front Audio Connector PwrledCdin CD In Connector Spdifi Spdif In ConnectorUSB1 / FUSB2 / FUSB3 Front USB Connector 17 F11394 / F21394 Front Ieee 1394 ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosStatus Page Setup Menu / Option Page Setup Menu Main MenuF12 Boot Menu Main Menu For example Bios Ver. F3cBios Setting Recovery „ Power Management Setup „ Standard Cmos Features„ Advanced Bios Features „ PnP/PCI ConfigurationIDE Channel 0 Master/Slave TimeIDE Channel 2/3/4/5/6/7 Master Halt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Hard Disk Boot PriorityBoot Up Floppy Seek Away Mode Password CheckInit Display First NV Sata 1 Secondary RAID NV Sata RAID functionNV Sata 1 Primary RAID NV Sata 2 Primary RAIDNV Sata 3 Primary RAID IDE Prefetch ModeNV Sata 2 Secondary RAID NV Sata 3 Secondary RAIDOnboard Onboard LAN Boot ROMParallel Port Mode Onboard Serial PortUSB Keyboard Support ECP Mode Use DMAOn-Chip USB USB Mouse SupportModem Ring On Power-On by AlarmPME Event Wake Up USB Resume from SuspendKB Power on Password Power On By MousePower On By Keyboard AC Back FunctionPCI 2 IRQ Assignment PnP/PCI ConfigurationsPCI 1 IRQ Assignment CPU Warning Temperature Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM Case OpenedCPU Smart FAN Mode CPU Smart FAN Control NoteCPU Clock Ratio CPU Frequency MHzPcie Clock MHz Robust Graphics BoosterCPU Voltage Control HT-Link VoltageCPU HT-Link Voltage Normal CPU VcoreLoad Fail-Safe Defaults Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview How to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Installing Sata hard drives in your computer Smart LAN Nvidia Mirror Step Save and exit Bios Setup GA-M57SLI-S4 Motherboard Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows SolutionsYES GA-M57SLI-S4 Motherboard Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English English English English English Contact Us Taiwan HeadquartersGigabyte Global Service System