Gigabyte GA-M57SLI-S4 user manual Load Fail-Safe Defaults

Page 49

2-8	Load Fail-Safe Defaults

	CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
	Standard CMOS Features	Load Fail-Safe Defaults
	Advanced BIOS Features	Load Optimized Defaults
	Integrated Peripherals	Set Supervisor Password
	Power Management Setup	Set User Password
	PnP/PCI Configurations	Load Fail-Safe DefaultsSave(Y/N)?& ExitN Setup
	PC Health Status	Exit Without Saving
	MB Intelligent Tweaker(M.I.T.)
	Esc: Quit	: Select Item	F11: Save CMOS to BIOS
	F8: Q-Flash	F10: Save & Exit Setup	F12: Load CMOS from BIOS
		Load Fail-Safe Defaults

Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance.

English

2-9	Load Optimized Defaults
	CMOS Setup Utility-Copyright (C) 1984-2005 Award Software
	Standard CMOS Features	Load Fail-Safe Defaults
	Advanced BIOS Features	Load Optimized Defaults
	Integrated Peripherals	Set Supervisor Password
	Power Management Setup	Set User Password
	PnP/PCI Configurations	Load Optimized DefaultsSave(Y/N)?& ExitN Setup
	PC Health Status	Exit Without Saving
	MB Intelligent Tweaker(M.I.T.)
	Esc: Quit	: Select Item	F11: Save CMOS to BIOS
	F8: Q-Flash	F10: Save & Exit Setup	F12: Load CMOS from BIOS
		Load Optimized Defaults

Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automati- cally detects.

- 49 -

BIOS Setup

Image 49

Contents GA-M57SLI-S4 Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-M57SLI-S4 Motherboard Layout Block Diagram Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerFeature Summary 4Mbit flash ROM Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Before you begin Setup of SLI Scalable Link Interface ConfigurationConnecting Two Graphics Cards Graphics Card Driver Setting I/O Back Panel Introduction Line Connectors IntroductionLine Out Front Speaker Out MICATX12V / ATX Power Connector 6 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector PCIE12V Power ConnectorIDE1 IDE Connector FDD FDD ConnectorEnglish Fpanel Front Panel Jumper Pwrled Faudio Front Audio ConnectorSpdifi Spdif In Connector Cdin CD In Connector17 F11394 / F21394 Front Ieee 1394 Connector USB1 / FUSB2 / FUSB3 Front USB ConnectorClrcmos Clear Cmos CI Chassis Intrusion, Case OpenMain Menu Status Page Setup Menu / Option Page Setup MenuF12 Boot Menu Main Menu For example Bios Ver. F3cBios Setting Recovery „ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 0 Master/Slave TimeIDE Channel 2/3/4/5/6/7 Master Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryFirst / Second / Third Boot Device Hard Disk Boot PriorityBoot Up Floppy Seek Away Mode Password CheckInit Display First NV Sata 1 Primary RAID NV Sata RAID functionNV Sata 1 Secondary RAID NV Sata 2 Primary RAIDNV Sata 2 Secondary RAID IDE Prefetch ModeNV Sata 3 Primary RAID NV Sata 3 Secondary RAIDParallel Port Mode Onboard LAN Boot ROMOnboard Onboard Serial PortOn-Chip USB ECP Mode Use DMAUSB Keyboard Support USB Mouse SupportPME Event Wake Up Power-On by AlarmModem Ring On USB Resume from SuspendPower On By Keyboard Power On By MouseKB Power on Password AC Back FunctionPCI 2 IRQ Assignment PnP/PCI ConfigurationsPCI 1 IRQ Assignment Current CPU/POWER/SYSTEM FAN Speed RPM Current CPU TemperatureCPU Warning Temperature Case OpenedCPU Smart FAN Control Note CPU Smart FAN ModePcie Clock MHz CPU Frequency MHzCPU Clock Ratio Robust Graphics BoosterCPU HT-Link Voltage HT-Link VoltageCPU Voltage Control Normal CPU VcoreLoad Fail-Safe Defaults Set Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview How to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Press Y on your keyboard to save and exit FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Installing Sata hard drives in your computer Smart LAN Nvidia Mirror Step Save and exit Bios Setup GA-M57SLI-S4 Motherboard Configuring RAID set in RAID Bios YES Nvidia Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Solutions Configuring a bootable RAID array with Microsoft WindowsYES GA-M57SLI-S4 Motherboard 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English English English English English Taiwan Headquarters Contact UsGigabyte Global Service System