Gigabyte GA-M57SLI-S4 user manual CPU HT-Link Voltage, CPU Voltage Control, Normal CPU Vcore

Page 48

English

HT-Link Voltage

Set the voltage settings for HT-Link.

NormalSet HT-Link voltage to Normal. (Default value)

+0.025V ~ +0.375V Set HT-Link voltage from +0.025V to +0.375V.

CPU HT-Link Voltage

Set the voltage settings for the HT-Link between CPU and chipset.

NormalSet CPU HT-Link voltage to Normal. (Default value)

+0.025V ~ +0.375V Set CPU HT-Link voltage from +0.025V to +0.375V.

CPU Voltage Control

Please note that by overclocking your system through the increase of the CPU voltage, damage to the CPU or decrease in the CPU life expectancy may occur.

Supports adjustable CPU Voltage from 0.8000V to 1.5500V. (Default value: Normal)

Normal CPU Vcore

Display your CPU Vcore Voltage.

GA-M57SLI-S4 Motherboard

- 48 -

Image 48

Contents GA-M57SLI-S4 Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-M57SLI-S4 Motherboard Layout Block Diagram Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary 4Mbit flash ROM Installation of the CPU and CPU Cooler Installation of the CPUInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards Setup of SLI Scalable Link Interface Configuration Before you beginConnecting Two Graphics Cards Graphics Card Driver Setting I/O Back Panel Introduction Connectors Introduction LineLine Out Front Speaker Out MICATX12V / ATX Power Connector PCIE12V Power Connector 6 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorFDD FDD Connector IDE1 IDE ConnectorEnglish Fpanel Front Panel Jumper Faudio Front Audio Connector PwrledCdin CD In Connector Spdifi Spdif In ConnectorUSB1 / FUSB2 / FUSB3 Front USB Connector 17 F11394 / F21394 Front Ieee 1394 ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosStatus Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F3c F12 Boot MenuBios Setting Recovery „ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationTime IDE Channel 0 Master/SlaveIDE Channel 2/3/4/5/6/7 Master Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryHard Disk Boot Priority First / Second / Third Boot DeviceBoot Up Floppy Seek Password Check Away ModeInit Display First NV Sata RAID function NV Sata 1 Primary RAIDNV Sata 1 Secondary RAID NV Sata 2 Primary RAIDIDE Prefetch Mode NV Sata 2 Secondary RAIDNV Sata 3 Primary RAID NV Sata 3 Secondary RAIDOnboard LAN Boot ROM Parallel Port ModeOnboard Onboard Serial PortECP Mode Use DMA On-Chip USBUSB Keyboard Support USB Mouse SupportPower-On by Alarm PME Event Wake UpModem Ring On USB Resume from SuspendPower On By Mouse Power On By KeyboardKB Power on Password AC Back FunctionPnP/PCI Configurations PCI 2 IRQ AssignmentPCI 1 IRQ Assignment Current CPU Temperature Current CPU/POWER/SYSTEM FAN Speed RPMCPU Warning Temperature Case OpenedCPU Smart FAN Mode CPU Smart FAN Control NoteCPU Frequency MHz Pcie Clock MHzCPU Clock Ratio Robust Graphics BoosterHT-Link Voltage CPU HT-Link VoltageCPU Voltage Control Normal CPU VcoreLoad Fail-Safe Defaults Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Installing Sata hard drives in your computer Smart LAN Nvidia Mirror Step Save and exit Bios Setup GA-M57SLI-S4 Motherboard Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows SolutionsYES GA-M57SLI-S4 Motherboard Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English English English English English Contact Us Taiwan HeadquartersGigabyte Global Service System