Gigabyte GA-K8N51GMF-9-RH user manual Cdin CD In Connector, Pwrled

Page 24

English

10)CD_IN (CD In Connector)

Connect CD-ROM or DVD-ROM audio out to the connector.

			Pin No.	Definition
	1		1	CD-L
			2	GND
			2	GND
			3	GND
			4	CD-R

11)PWR_LED

PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode.

	Pin No.	Definition
	1	MPD+
1	2	MPD-
	3	MPD-

GA-K8N51GMF-9-RH Motherboard

- 24 -

Image 24

Contents GA-K8N51GMF-9-RH Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-K8N51GMF-9-RH Motherboard Layout Block Diagram Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary 4Mbit flash ROM Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Center/Subwoofer Speaker OutSide Speaker Out ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by nForceFaudio Front Audio Connector Fpanel Front Panel Jumper Cdin CD In Connector PwrledUSB1 / FUSB2 Front USB Connector 13 F11394 Ieee 1394 ConnectorComa Coma Connector Spdifio Spdif In/OutClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBattery Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F3a F12 For Boot Menu„ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationStandard Cmos Features TimeIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Floppy 3 Mode Support for Japan Area Drive aHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Up Floppy SeekPassword Check Init Display FirstFrame Buffer Size Onboard GPUIntegrated Peripherals SPPSATA-II 2 Primary RAID SATA-II 2 Secondary RAIDOn-Chip IDE Channel0 On-Chip IDE Channel1Onboard LAN Boot ROM Parallel Port ModeOnboard LAN Function Onboard 1394 FunctionPower Management Setup Power-On by AlarmPME Event Wake Up Modem Ring OnPower On By Keyboard KB Power on PasswordPower On By Mouse AC Back FunctionPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status Frequency/Voltage Control CPU FrequencyPcie Clock K8 CPU Clock RatioLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewXpress Recovery2 Introduction How to use the Xpress Recovery2System requirements Main Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Before you begin SPP SCSI-0 Nvidia Mirror Step Save and exit Bios Setup Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows SolutionsYES English Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting AMI Bios Beep CodesEnglish English English Contact Us Taiwan HeadquartersChina Shanghai