Gigabyte GA-K8N51GMF-9-RH user manual Battery

Page 28

English

18) BATTERY

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions.

If you want to erase CMOS...

1.Turn OFF the computer and unplug the power cord.

2.Take out the battery gently and put it aside for about 10 minutes. (Or you can use a metal object to connect the positive and nega- tive pins in the battery holder to makethem short for one minute.)

3.Re-install the battery.

4.Plug the power cord and turn ON the computer.

GA-K8N51GMF-9-RH Motherboard

- 28 -

Image 28
Contents GA-K8N51GMF-9-RH Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-K8N51GMF-9-RH Motherboard Layout Block Diagram Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary 4Mbit flash ROM Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Center/Subwoofer Speaker Out Connectors IntroductionSide Speaker Out ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by nForceFaudio Front Audio Connector Fpanel Front Panel Jumper Cdin CD In Connector PwrledUSB1 / FUSB2 Front USB Connector 13 F11394 Ieee 1394 ConnectorComa Coma Connector Spdifio Spdif In/OutClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBattery Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F3a F12 For Boot Menu„ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationTime Standard Cmos FeaturesIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Floppy 3 Mode Support for Japan Area Drive aHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Up Floppy SeekPassword Check Init Display FirstFrame Buffer Size Onboard GPUIntegrated Peripherals SPPSATA-II 2 Primary RAID SATA-II 2 Secondary RAIDOn-Chip IDE Channel0 On-Chip IDE Channel1Onboard LAN Boot ROM Parallel Port ModeOnboard LAN Function Onboard 1394 FunctionPower Management Setup Power-On by AlarmPME Event Wake Up Modem Ring OnPower On By Keyboard KB Power on PasswordPower On By Mouse AC Back FunctionPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status Frequency/Voltage Control CPU FrequencyPcie Clock K8 CPU Clock RatioLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewHow to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Before you begin SPP SCSI-0 Nvidia Mirror Step Save and exit Bios Setup Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows SolutionsYES English Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting AMI Bios Beep CodesEnglish English English Contact Us Taiwan HeadquartersChina Shanghai