Gigabyte GA-K8N51GMF-9-RH Entering the Q-FlashTMutility, Task menu for Dual Bios utility

Page 56

English

Entering the Q-FlashTMutility:

Step1: To use Q-Flash utility, you must press Del in the boot screen to enter BIOS menu.

CMOS Setup Utility-Copyright (C) 1984-2004 Award Software

Standard CMOS Features	Select Language
Advanced BIOS Features	Load Fail-Safe Defaults
Integrated Peripherals	Load Optimized Defaults
Power Management Setup	Set Supervisor Password
PnP/PCI Configurations	Set User Password
PC Health Status	Save & Exit Setup
MB Intelligent Tweaker(M.I.T.)	Exit Without Saving
ESC: Quit	F3: Change Language
F8: Dual BIOS/Q-Flash	F10: Save & Exit Setup
	Time, Date, Hard Disk Type...

Step 2: Press F8 button on your keyboard and then Y button to enter the Dual BIOS/Q-Flash utility.

Exploring the Q-FlashTM / Dual BIOS utility screen

The Q-Flash / Dual BIOS utility screen consists of the following key components.

Task menu for Dual BIOS utility

Task menu for Q-FlashTMutility

									Dual BIOS utility bar
			Dual BIOS Utility
			Dual BIOS Utility

		Boot From		Main Bios
		Main ROM Type/Size		SST 49LF003A		512K
		Backup ROM Type/Size		SST 49LF003A		512K
		Wide Range Protection		Disable
			Boot From	Main Bios
			Auto Recovery	Enable
			Halt On Error	Disable
			Copy Main ROM Data to Backup
			Load Default Settings
			Save Settings to CMOS						Q-FlashTMutility title
			Save Settings to CMOS
			Q-Flash Utility
			Q-Flash Utility
			Load Main BIOS from Floppy						bar
			Load Backup BIOS from Floppy						bar
			Save Main BIOS to Floppy
			Save Backup BIOS to Floppy						Action bar
			Save Backup BIOS to Floppy
		Enter : Run	:Move	ESC:Reset	F10:Power Off
		Enter : Run	:Move	ESC:Reset	F10:Power Off

Task menu for Dual BIOS utility:

Contains the names of eight tasks and two item showing information about the BIOS ROM type. Blocking a task and pressing Enter key on your keyboard to enable execution of the task.

Task menu for Q-Flash utility:

Contains the names of four tasks. Blocking a task and pressing Enter key on your keyboard to enable execu- tion of the task.

Action bar:

Contains the names of four actions needed to operate the Q-Flash/Dual BIOS utility. Pressing the buttons mentioned on your keyboards to perform these actions.

GA-K8N51GMF-9-RH Motherboard

- 56 -

Image 56

Contents GA-K8N51GMF-9-RH Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-K8N51GMF-9-RH Motherboard Layout Block Diagram Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary 4Mbit flash ROM Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Side Speaker Out Connectors IntroductionCenter/Subwoofer Speaker Out ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by nForceFaudio Front Audio Connector Fpanel Front Panel Jumper Cdin CD In Connector PwrledUSB1 / FUSB2 Front USB Connector 13 F11394 Ieee 1394 ConnectorComa Coma Connector Spdifio Spdif In/OutClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBattery Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F3a F12 For Boot Menu„ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Standard Cmos FeaturesTime Floppy 3 Mode Support for Japan Area Drive aHalt on MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Up Floppy SeekPassword Check Init Display FirstFrame Buffer Size Onboard GPUIntegrated Peripherals SPPSATA-II 2 Primary RAID SATA-II 2 Secondary RAIDOn-Chip IDE Channel0 On-Chip IDE Channel1Onboard LAN Boot ROM Parallel Port ModeOnboard LAN Function Onboard 1394 FunctionPower Management Setup Power-On by AlarmPME Event Wake Up Modem Ring OnPower On By Keyboard KB Power on PasswordPower On By Mouse AC Back FunctionPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status Frequency/Voltage Control CPU FrequencyPcie Clock K8 CPU Clock RatioLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewSystem requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Before you begin SPP SCSI-0 Nvidia Mirror Step Save and exit Bios Setup Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows SolutionsYES English Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting AMI Bios Beep CodesEnglish English English Contact Us Taiwan HeadquartersChina Shanghai