Gigabyte GA-K8N51GMF-9-RH Onboard LAN Function, Onboard LAN Boot ROM, Onboard 1394 Function

Page 38

English

Onboard LAN Function

Auto

Auto-detect onboard LAN chip function.(Default value)

Disabled

Disable onboard LAN chip function.

Onboard LAN Boot ROM

This function decide whether to invoke the boot ROM of the onboard LAN chip.

Enabled

Enable this function.

Disabled

Disable this function. (Default value)

Onboard 1394 Function

Enabled

Enable onboard IEEE1394 function.(Default value)

Disabled

Disable onboard IEEE1394 function.

Onboard Serial Port 1

Auto

BIOS will automatically setup the port 1 address.

3F8/IRQ4

Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)

2F8/IRQ3

Enable onboard Serial port 1 and address is 2F8/IRQ3.

3E8/IRQ4

Enable onboard Serial port 1 and address is 3E8/IRQ4.

2E8/IRQ3

Enable onboard Serial port 1 and address is 2E8/IRQ3.

Disabled

Disable onboard Serial port 1.

Onboard Parallel Port

Disabled

Disable onboard LPT port.

378/IRQ7

Enable onboard LPT port and address is 378/IRQ7. (Default value)

278/IRQ5

Enable onboard LPT port and address is 278/IRQ5.

3BC/IRQ7

Enable onboard LPT port and address is 3BC/IRQ7.

Parallel Port Mode

SPP

Using Parallel port as Standard Parallel Port. (Default value)

EPP

Using Parallel port as Enhanced Parallel Port.

ECP

Using Parallel port as Extended Capabilities Port.

ECP+EPP

Using Parallel port as ECP and EPP mode.

GA-K8N51GMF-9-RH Motherboard

- 38 -

Image 38
Contents GA-K8N51GMF-9-RH Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-K8N51GMF-9-RH Motherboard Layout Block Diagram Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary 4Mbit flash ROM Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Side Speaker Out Connectors IntroductionCenter/Subwoofer Speaker Out ATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by nForceFaudio Front Audio Connector Fpanel Front Panel Jumper Cdin CD In Connector PwrledUSB1 / FUSB2 Front USB Connector 13 F11394 Ieee 1394 ConnectorComa Coma Connector Spdifio Spdif In/OutClrcmos Clear Cmos CI Chassis Intrusion, Case OpenBattery Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F3a F12 For Boot Menu„ Power Management Setup „ Standard Cmos Features„ Advanced Bios Features „ PnP/PCI ConfigurationIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Standard Cmos FeaturesTime Halt on Floppy 3 Mode Support for Japan AreaDrive a MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Boot Up Floppy SeekFrame Buffer Size Password CheckInit Display First Onboard GPUIntegrated Peripherals SPPOn-Chip IDE Channel0 SATA-II 2 Primary RAIDSATA-II 2 Secondary RAID On-Chip IDE Channel1Onboard LAN Function Onboard LAN Boot ROMParallel Port Mode Onboard 1394 FunctionPME Event Wake Up Power Management SetupPower-On by Alarm Modem Ring OnPower On By Mouse Power On By KeyboardKB Power on Password AC Back FunctionPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status Pcie Clock Frequency/Voltage ControlCPU Frequency K8 CPU Clock RatioLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 Introduction User Interface OverviewSystem requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen EnglishCongratulation!! You have updated Bios successfully Bios file becomes F4 after updatingMethod 2 @BIOSTM Utility Methods and stepsEnglish Before you begin SPP SCSI-0 Nvidia Mirror Step Save and exit Bios Setup Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows SolutionsYES English Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting AMI Bios Beep CodesEnglish English English Contact Us Taiwan HeadquartersChina Shanghai