Gigabyte GA-M55S-S3 user manual FDD FDD Connector, IDE1 IDE Connector

Page 21

7)FDD (FDD Connector)

The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB. Before attaching the FDD cable, please take note of the foolproof groove in the FDD connector.

33	1
34	2

8)IDE1 (IDE Connector)

An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device). Before attaching the IDE cable, please take note of the foolproof groove in the IDE connector.

4039

21

English

- 21 -

Hardware Installation

Image 21

Contents GA-M55S-S3 rev Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-M55S-S3 GA-M55S-S3 rev .0 Motherboard LayoutBlock Diagram Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerFeature Summary 4Mbit flash ROM Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Line Connectors IntroductionLine Out Front Speaker Out MICATX12V / ATX Power Connector 6 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector PCIE12V Power ConnectorIDE1 IDE Connector FDD FDD ConnectorBattery Fpanel Front Panel Jumper Pwrled Faudio Front Audio ConnectorSpdifi S/PDIF In Connector Cdin CD In Connector17 F11394 / F21394 Front Ieee 1394 Connector USB1 / FUSB2 / FUSB3 Front USB ConnectorClrcmos Clear Cmos CI Chassis Intrusion, Case OpenEnglish Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. FAa F12 For Boot MenuBios Setting Recovery „ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationTime IDE Channel 0 Master/SlaveIDE Channel 2/3/4/5 Master Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority First / Second / Third Boot DeviceBoot Up Floppy Seek Password Check Away ModeInit Display First Integrated Peripherals NV Sata 2 Secondary RAID IDE Prefetch ModeOn-Chip IDE Channel0 On-Chip MAC LanParallel Port Mode Onboard LAN Boot ROMOnboard Onboard Serial PortOn-Chip USB ECP Mode Use DMAUSB Keyboard Support USB Mouse SupportPME Event Wake Up Power-On by AlarmModem Ring On USB Resume from SuspendPower On By Keyboard Power On By MouseKB Power on Password AC Back FunctionPnP/PCI Configurations PCI 2 IRQ AssignmentPCI 1 IRQ Assignment Current CPU/POWER/SYSTEM FAN Speed RPM Current CPU TemperatureCPU Warning Temperature CPU/POWER/SYSTEM FAN Fail WarningCPU Smart FAN Control Note CPU Smart FAN ModePcie Clock MHz CPU Frequency MHzCPU Clock Ratio DDR2 Voltage ControlCPU HT-Link Voltage CPU Voltage ControlNormal CPU Vcore Load Fail-Safe Defaults Set Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview How to use the Xpress Recovery2 Xpress Recovery2 IntroductionBoot from CD/DVD F9 Xpress Recovery2 System requirementsMain Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to Press Y on your keyboard to save and exit FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Installing Sata hard drives in your computer Smart LAN Step Save and exit Bios Setup Configuring RAID set in RAID Bios YES BBS Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English English Taiwan Headquarters Contact UsGigabyte Global Service System