Gigabyte GA-M55S-S3 user manual Integrated Peripherals

Page 36

English

2-3	Integrated Peripherals

			CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
				Integrated Peripherals
	Serial-ATA RAID Config				[Press Enter]		Item Help
	On-Chip IDE Channel0				[Enabled]		Menu Level
	On-Chip MAC Lan				[Auto]
	NV Serial-ATA Controller				[All Enabled]
	IDE Prefetch Moed				[Enabled]
	Onboard Audio Function				[Auto]
	SMART LAN				[Press Enter]
	Onboard 1394				[Enabled]
	Onboard LAN Boot ROM				[Disabled]
	Onboard Serial Port 1				[3F8/IRQ4]
	Onboard Parallel Port				[378/IRQ7]
	Parallel Port Mode				[SPP]
x ECP Mode Use DMA					3
	On-Chip USB				[V1.1+V2.0]
	USB Keyboard Support				[Disabled]
	USB Mouse Support				[Disabled]
	Legacy USB storage detect				[Enabled]
	: Move	Enter: Select		+/-/PU/PD: Value		F10: Save	ESC: Exit	F1: General Help
	F5: Previous Values			F6: Fail-Safe Defaults			F7: Optimized Defaults

Serial-ATA RAID Config
			CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
				Serial-ATA RAID Config
	NV SATA RAID function				[Disabled]		Item Help
x NV SATA 1 Primary RAID					Enabled		Menu Level
x	NV SATA 1 Secondary RAID				Enabled
x NV SATA 2 Primary RAID					Enabled
x	NV SATA 2 Secondary RAID				Enabled
	: Move	Enter: Select		+/-/PU/PD: Value		F10: Save	ESC: Exit	F1: General Help
	F11/12: Profile		F5: Previous Values		F6: Fail-Safe Defaults		F7: Optimized Defaults
NV SATA RAID function
	Enabled		Allows users to configure individual SATA channels as RAID or ATA mode.
	Disabled		Disable the RAID function for all of the onboard SATA channels. (Default value)
NV SATA 1 Primary RAID
	Enabled		Enable RAID function for the first channel of the first SATA controller. (Default value)
	Disabled		Disable the RAID function of this channel. It will operate in ATA mode.
NV SATA 1 Secondary RAID
	Enabled		Enable RAID function for the second channel of the first SATA controller. (Default value)
	Disabled		Disable the RAID function of this channel. It will operate in ATA mode.
NV SATA 2 Primary RAID
	Enabled		Enable RAID function for the first channel of the second SATA controller. (Default value)
	Disabled		Disable the RAID function of this channel. It will operate in ATA mode.

GA-M55S-S3 (rev. 2.0) Motherboard

- 36 -

Image 36

Contents GA-M55S-S3 rev Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-M55S-S3 rev .0 Motherboard Layout GA-M55S-S3Block Diagram Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary 4Mbit flash ROM Installation of the CPU and CPU Cooler Installation of the CPUInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction LineLine Out Front Speaker Out MICATX12V / ATX Power Connector PCIE12V Power Connector 6 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorFDD FDD Connector IDE1 IDE ConnectorBattery Fpanel Front Panel Jumper Faudio Front Audio Connector PwrledCdin CD In Connector Spdifi S/PDIF In ConnectorUSB1 / FUSB2 / FUSB3 Front USB Connector 17 F11394 / F21394 Front Ieee 1394 ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosEnglish Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. FAa F12 For Boot MenuBios Setting Recovery „ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationTime IDE Channel 0 Master/SlaveIDE Channel 2/3/4/5 Master Floppy 3 Mode Support for Japan Area Drive a / Drive BHalt on MemoryHard Disk Boot Priority First / Second / Third Boot DeviceBoot Up Floppy Seek Password Check Away ModeInit Display First Integrated Peripherals IDE Prefetch Mode NV Sata 2 Secondary RAIDOn-Chip IDE Channel0 On-Chip MAC LanOnboard LAN Boot ROM Parallel Port ModeOnboard Onboard Serial PortECP Mode Use DMA On-Chip USBUSB Keyboard Support USB Mouse SupportPower-On by Alarm PME Event Wake UpModem Ring On USB Resume from SuspendPower On By Mouse Power On By KeyboardKB Power on Password AC Back FunctionPnP/PCI Configurations PCI 2 IRQ AssignmentPCI 1 IRQ Assignment Current CPU Temperature Current CPU/POWER/SYSTEM FAN Speed RPMCPU Warning Temperature CPU/POWER/SYSTEM FAN Fail WarningCPU Smart FAN Mode CPU Smart FAN Control NoteCPU Frequency MHz Pcie Clock MHzCPU Clock Ratio DDR2 Voltage ControlCPU HT-Link Voltage CPU Voltage ControlNormal CPU Vcore Load Fail-Safe Defaults Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview Xpress Recovery2 Introduction How to use the Xpress Recovery2Boot from CD/DVD F9 Xpress Recovery2 System requirementsMain Screen of Xpress Recovery2 PrecautionsLimitations Flash Bios Method Introduction Method 1 Q-FlashTMUtilityBefore You Begin Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Installing Sata hard drives in your computer Smart LAN Step Save and exit Bios Setup Configuring RAID set in RAID Bios YES BBS Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English English Contact Us Taiwan HeadquartersGigabyte Global Service System