Gigabyte GA-M55S-S3 user manual Battery

Page 22

English

9)SATAII1 / 2 / 3 / 4 (SATA 3Gb/s Connectors, Controlled by nForce 550)

SATA 3Gb/s can provide up to 300MB/s transfer rate. Please refer to the BIOS setting for the SATA 3Gb/s and install the proper driver in order to work properly.

 

 

 

Pin No.

Definition

SATAII4

 

 

1

GND

 

 

2

TXP

 

 

 

 

 

 

3

TXN

 

 

 

4

GND

 

 

1

5

RXN

 

 

 

6

RXP

 

 

7

7

GND

 

 

 

 

SATAII1

SATAII2

SATAII3

 

 

10) BATTERY

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions.

If you want to erase CMOS...

1. Turn off the computer and unplug the power cord.

2. Gently take out the battery and put it aside for about one minute. (Or you can use a metal object to connect the positive and negative pins in the battery holder to make them short for five seconds.)

3.Re-install the battery.

4.Plug the power cord in and turn on the computer.

GA-M55S-S3 (rev. 2.0) Motherboard

- 22 -

Image 22
Contents GA-M55S-S3 rev Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Item Checklist GA-M55S-S3 rev .0 Motherboard Layout GA-M55S-S3Block Diagram Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary 4Mbit flash ROM Installation of the CPU and CPU Cooler Installation of the CPUInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Line Out Front Speaker Out Connectors IntroductionLine MICATX12V / ATX Power Connector PCIE12V Power Connector 6 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorFDD FDD Connector IDE1 IDE ConnectorBattery Fpanel Front Panel Jumper Faudio Front Audio Connector PwrledCdin CD In Connector Spdifi S/PDIF In ConnectorUSB1 / FUSB2 / FUSB3 Front USB Connector 17 F11394 / F21394 Front Ieee 1394 ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosEnglish Status Page Setup Menu / Option Page Setup Menu Main MenuF12 For Boot Menu Main Menu For example Bios Ver. FAaBios Setting Recovery „ Power Management Setup „ Standard Cmos Features„ Advanced Bios Features „ PnP/PCI ConfigurationIDE Channel 0 Master/Slave TimeIDE Channel 2/3/4/5 Master Halt on Floppy 3 Mode Support for Japan AreaDrive a / Drive B MemoryFirst / Second / Third Boot Device Hard Disk Boot PriorityBoot Up Floppy Seek Away Mode Password CheckInit Display First Integrated Peripherals On-Chip IDE Channel0 IDE Prefetch ModeNV Sata 2 Secondary RAID On-Chip MAC LanOnboard Onboard LAN Boot ROMParallel Port Mode Onboard Serial PortUSB Keyboard Support ECP Mode Use DMAOn-Chip USB USB Mouse SupportModem Ring On Power-On by AlarmPME Event Wake Up USB Resume from SuspendKB Power on Password Power On By MousePower On By Keyboard AC Back FunctionPCI 2 IRQ Assignment PnP/PCI ConfigurationsPCI 1 IRQ Assignment CPU Warning Temperature Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM CPU/POWER/SYSTEM FAN Fail WarningCPU Smart FAN Mode CPU Smart FAN Control NoteCPU Clock Ratio CPU Frequency MHzPcie Clock MHz DDR2 Voltage ControlCPU Voltage Control CPU HT-Link VoltageNormal CPU Vcore Load Fail-Safe Defaults Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Applications Driver CD InformationHardware Information Contact UsEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview Boot from CD/DVD F9 Xpress Recovery2 Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 System requirementsPrecautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Installing Sata hard drives in your computer Smart LAN Step Save and exit Bios Setup Configuring RAID set in RAID Bios YES BBS Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English English Contact Us Taiwan HeadquartersGigabyte Global Service System