Gigabyte GA-M55S-S3 user manual Load Fail-Safe Defaults

Page 47

2-8	Load Fail-Safe Defaults

	CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
	Standard CMOS Features	Load Fail-Safe Defaults
	Advanced BIOS Features	Load Optimized Defaults
	Integrated Peripherals	Set Supervisor Password
	Power Management Setup	Set User Password
	PnP/PCI Configurations	Load Fail-Safe DefaultsSave(Y/N)?& ExitN Setup
	PC Health Status	Exit Without Saving
	MB Intelligent Tweaker(M.I.T.)
	Esc: Quit	: Select Item	F11: Save CMOS to BIOS
	F8: Q-Flash	F10: Save & Exit Setup	F12: Load CMOS from BIOS
		Load Fail-Safe Defaults

Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance.

English

2-9	Load Optimized Defaults
	CMOS Setup Utility-Copyright (C) 1984-2006 Award Software
	Standard CMOS Features	Load Fail-Safe Defaults
	Advanced BIOS Features	Load Optimized Defaults
	Integrated Peripherals	Set Supervisor Password
	Power Management Setup	Set User Password
	PnP/PCI Configurations	Load Optimized DefaultsSave(Y/N)?& ExitN Setup
	PC Health Status	Exit Without Saving
	MB Intelligent Tweaker(M.I.T.)
	Esc: Quit	: Select Item	F11: Save CMOS to BIOS
	F8: Q-Flash	F10: Save & Exit Setup	F12: Load CMOS from BIOS
		Load Optimized Defaults

Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automati- cally detects.

- 47 -

BIOS Setup

Image 47

Contents GA-M55S-S3 rev Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation Item Checklist GA-M55S-S3 GA-M55S-S3 rev .0 Motherboard LayoutBlock Diagram Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyFeature Summary 4Mbit flash ROM Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction MIC Connectors IntroductionLine Line Out Front Speaker OutATX12V / ATX Power Connector 6 Cpufan / Sysfan / Pwrfan Cooler Fan Power Connector PCIE12V Power ConnectorIDE1 IDE Connector FDD FDD ConnectorBattery Fpanel Front Panel Jumper Pwrled Faudio Front Audio ConnectorSpdifi S/PDIF In Connector Cdin CD In Connector17 F11394 / F21394 Front Ieee 1394 Connector USB1 / FUSB2 / FUSB3 Front USB ConnectorClrcmos Clear Cmos CI Chassis Intrusion, Case OpenEnglish Main Menu Status Page Setup Menu / Option Page Setup MenuBios Setting Recovery Main Menu For example Bios Ver. FAaF12 For Boot Menu „ PnP/PCI Configuration „ Standard Cmos Features„ Advanced Bios Features „ Power Management SetupIDE Channel 2/3/4/5 Master TimeIDE Channel 0 Master/Slave Memory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onBoot Up Floppy Seek Hard Disk Boot PriorityFirst / Second / Third Boot Device Init Display First Password CheckAway Mode Integrated Peripherals On-Chip MAC Lan IDE Prefetch ModeNV Sata 2 Secondary RAID On-Chip IDE Channel0Onboard Serial Port Onboard LAN Boot ROMParallel Port Mode OnboardUSB Mouse Support ECP Mode Use DMAOn-Chip USB USB Keyboard SupportUSB Resume from Suspend Power-On by AlarmPME Event Wake Up Modem Ring OnAC Back Function Power On By MousePower On By Keyboard KB Power on PasswordPCI 1 IRQ Assignment PnP/PCI ConfigurationsPCI 2 IRQ Assignment CPU/POWER/SYSTEM FAN Fail Warning Current CPU TemperatureCurrent CPU/POWER/SYSTEM FAN Speed RPM CPU Warning TemperatureCPU Smart FAN Control Note CPU Smart FAN ModeDDR2 Voltage Control CPU Frequency MHzPcie Clock MHz CPU Clock RatioNormal CPU Vcore CPU HT-Link VoltageCPU Voltage Control Load Fail-Safe Defaults Set Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Boot from CD/DVD F9 Xpress Recovery2Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to Press Y on your keyboard to save and exit FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Installing Sata hard drives in your computer Smart LAN Step Save and exit Bios Setup Configuring RAID set in RAID Bios YES BBS Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English English Taiwan Headquarters Contact UsGigabyte Global Service System