Gigabyte GA-K8N51PVMT-9-RH SATA-II 2 Secondary RAID, On-Chip IDE Channel0, On-Chip IDE Channel1

Page 37

SATA-II 2 Primary RAID

Enabled

Enable SATAII 2 1st SATA RAID function.

Disabled

Disable this function. (Default value)

SATA-II 2 Secondary RAID

Enabled

Enable SATAII 2 2nd SATA RAID function.

Disabled

Disable this function. (Default value)

On-Chip IDE Channel0

Enabled

Enable onboard 1st channel IDE port. (Default value)

Disabled

Disable onboard 1st channel IDE port.

On-Chip IDE Channel1

Enabled

Enable onboard 2nd channel IDE port. (Default value)

Disabled

Disable onboard 2nd channel IDE port.

IDE1 Conductor Cable

Auto

BIOS autodetects IDE1 conductor cable .(Default Value)

ATA66/100/133 Set IDE1 Conductor Cable to ATA66/100/133 (Please make sure your IDE

 

device and cable are compatible with ATA66/100/133).

ATA33

Set IDE1 Conductor Cable to ATA33. (Please make sure your IDE device

 

and cable are compatible with ATA33)

IDE2 Conductor Cable

Auto BIOS autodetects IDE2 conductor cable. (Default Value)

ATA66/100/133 Set IDE2 Conductor Cable to ATA66/100/133. (Please make sure your IDE

 

device and cable are compatible with ATA66/100/133)

ATA33

Set IDE2 Conductor Cable to ATA33. (Please make sure your IDE device

 

and cable are compatible with ATA33)

Serial-ATAII 1

Enabled

Enable Serial-ATAII 1 support. (Default Value)

Disabled

Disable Serial-ATAII 1 support.

Serial-ATAII 2

Enabled

Enable Serial-ATAII 2 support. (Default Value)

Disabled

Disable Serial-ATAII 2 support.

On-Chip USB

V1.1+V2.0

Enable USB 1.1 and USB 2.0 controllers. (Default Value)

V1.1

Enable only USB 1.1 controller

Disabled

Disable onchip USB support.

USB Keyboard Support

Enabled

Enable USB keyboard support.

Disabled

Disable USB keyboard support. (Default value)

USB Mouse Support

Enabled

Enable USB mouse support.

Disabled

Disable USB mouse support. (Default value)

English

- 37 -

BIOS Setup

Image 37
Contents GA-K8N51PVMT-9-RH Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation GA-K8N51PVMT-9-RH Motherboard Layout Block Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerLAN Feature Summary4Mbit flash ROM Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Svid OUT Connectors Introduction ATX12V / ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorSATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by nForce IDE1 / IDE2 IDE ConnectorBattery Fpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel Connector14 F11394 Ieee 1394 Connector USB1 / FUSB2 Front USB ConnectorSpdifio Spdif In/Out Coma Coma ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosMain Menu Status Page Setup Menu / Option Page Setup MenuF12 For Boot Menu Main Menu For example Bios Ver. F3a„ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationTime Standard Cmos FeaturesIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Drive a Floppy 3 Mode Support for Japan AreaMemory Base MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Boot Up Floppy SeekInit Display First Password CheckFrame Buffer Size Onboard GPUSPP Integrated PeripheralsOn-Chip IDE Channel0 SATA-II 2 Secondary RAIDOn-Chip IDE Channel1 IDE1 Conductor CableParallel Port Mode Onboard LAN Boot ROMOnboard Audio Function Onboard LAN FunctionPower-On by Alarm Power Management SetupPME Event Wake Up Modem Ring OnKB Power on Password Power On By KeyboardPower On By Mouse AC Back FunctionPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status CPU Smart FAN Control Note Frequency/Voltage Control Load Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupEnglish Install Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationConnecting the Video Output Devices EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview How to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Part Two FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Before you begin SPP SCSI-0 Nvidia Mirror Step Save and exit Bios Setup GA-K8N51PVMT-9-RH Motherboard Configuring RAID set in RAID Bios YES Nvidia Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Solutions Configuring a bootable RAID array with Microsoft WindowsYES English 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English Taiwan Headquarters Contact UsGigabyte Global Service System