Gigabyte GA-K8N51PVMT-9-RH user manual Frequency/Voltage Control

Page 44

English

2-7

Frequency/Voltage Control

 

 

 

 

 

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

 

 

 

 

Frequency/Voltage Control

 

 

 

CPU Frequency

 

[200.0]

 

 

Item Help

 

PCIE Clock

 

[100Mhz]

 

Menu Level`

 

K8 CPU Clock Ratio

[Default]

 

 

 

 

Display Output

 

[RGB]

 

 

 

 

TV Mode Support

[Disabled]

 

 

 

 

Robust Graphics Booster

[Auto]

 

 

 

KLJI: Move

Enter: Select

+/-/PU/PD: Value

F10: Save

ESC: Exit

F1: General Help

 

F5: Previous Values

F6: Fail-Safe Defaults

 

F7: Optimized Defaults

 

 

 

 

 

 

 

Incorrect using these features may cause your system broken. For power end-user use only.

CPU Frequency

200.0~300.0MHz Set CPU Frequency from 200MHz to 300MHz.

PCIE Clock

100~145MHz Set PCIE Clock from 100MHz to 145MHz.

K8 CPU Clock Ratio

This setup option will automatically assign by CPU detection. The option will display "Locked" and read only or will not show up if the CPU ratio is not changeable.

Display Output

This feature allows you to set signal output from the D-Sub(VGA) or S-Video(TV) port.

RGB

Set signal output from the D-Sub port. (Default value)

TV

Set signal output from the S-Video port.

AUTO

The signal will output from S-Video if you connect the output device to the S-Video

 

port. If there is no output device on the S-Video port, the signal will output from D-Sub.

TV Mode Support

Select the TV system, the options include: NTSC-M, NTSC-J, PAL-M, PAL-BDGHI, PAL-N and PAL-NC.

Disabled Disable this function. (Default value)

Robust Graphics Booster

Select the options can enhance the VGA graphics card bandwidth to get higher performance.

Auto

Set Robust Graphics Booster to Auto. (Default value)

Fast

Set Robust Graphics Booster to Fast.

Turbo

Set Robust Graphics Booster to Turbo.

GA-K8N51PVMT-9-RH Motherboard

- 44 -

Image 44
Contents GA-K8N51PVMT-9-RH Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8N51PVMT-9-RH Motherboard Layout Block Diagram Page Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary LAN4Mbit flash ROM Installation of the CPU and CPU Cooler Installation of the CPUInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Svid OUT Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by nForceBattery Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorUSB1 / FUSB2 Front USB Connector 14 F11394 Ieee 1394 ConnectorComa Coma Connector Spdifio Spdif In/OutClrcmos Clear Cmos CI Chassis Intrusion, Case OpenStatus Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F3a F12 For Boot Menu„ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Standard Cmos FeaturesTime Floppy 3 Mode Support for Japan Area Drive aMemory Base MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Up Floppy SeekPassword Check Init Display FirstFrame Buffer Size Onboard GPUIntegrated Peripherals SPPSATA-II 2 Secondary RAID On-Chip IDE Channel0On-Chip IDE Channel1 IDE1 Conductor CableOnboard LAN Boot ROM Parallel Port ModeOnboard Audio Function Onboard LAN FunctionPower Management Setup Power-On by AlarmPME Event Wake Up Modem Ring OnPower On By Keyboard KB Power on PasswordPower On By Mouse AC Back FunctionPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status CPU Smart FAN Control Note Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsConnecting the Video Output Devices User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to 4 to flash the backup BIOS, too Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Before you begin SPP SCSI-0 Nvidia Mirror Step Save and exit Bios Setup GA-K8N51PVMT-9-RH Motherboard Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows SolutionsYES English Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English Contact Us Taiwan HeadquartersGigabyte Global Service System