Gigabyte GA-K8N51PVMT-9-RH user manual Set Supervisor/User Password

Page 46

English

2-10

Set Supervisor/User Password

 

 

 

 

CMOS Setup Utility-Copyright (C) 1984-2006 Award Software

`

Standard CMOS Features

Load Fail-Safe Defaults

`

Advanced BIOS Features

Load Optimized Defaults

`

Integrated Peripherals

Set Supervisor Password

`

Power Management Setup

Set User Password

`

PnP/PCI ConfigurationsEnter Password:

Save & Exit Setup

`

PC Health Status

Exit Without Saving

`

Frequency/Voltage Control

 

Esc: Quit

KLJI: Select Item

F8: Q-Flash

F10: Save & Exit Setup

 

Change/Set/Disable Password

 

 

 

When you select this function, the following message will appear at the center of the screen to assist you in creating a password.

Type the password, up to eight characters, and press <Enter>. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a password.

To disable password, just press <Enter> when you are prompted to enter password. A message "PASSWORD DISABLED" will appear to confirm the password being disabled. Once the password is disabled, the system will boot and you can enter Setup freely.

The BIOS Setup program allows you to specify two separate passwords:

SUPERVISOR PASSWORD and a USER PASSWORD. When disabled, anyone may access all BIOS Setup program function. When enabled, the Supervisor password is required for entering the BIOS Setup program and having full configuration fields, the User password is required to access only basic items.

If you select "System" at "Password Check" in Advance BIOS Features Menu, you will be prompted for the password every time the system is rebooted or any time you try to enter Setup Menu.

If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted only when you try to enter Setup.

GA-K8N51PVMT-9-RH Motherboard

- 46 -

Image 46
Contents GA-K8N51PVMT-9-RH Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8N51PVMT-9-RH Motherboard Layout Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary LAN4Mbit flash ROM Installation of the CPU and CPU Cooler Installation of the CPUInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Svid OUT Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector SATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by nForceBattery Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorUSB1 / FUSB2 Front USB Connector 14 F11394 Ieee 1394 ConnectorComa Coma Connector Spdifio Spdif In/OutClrcmos Clear Cmos CI Chassis Intrusion, Case OpenStatus Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F3a F12 For Boot Menu„ Power Management Setup „ Standard Cmos Features„ Advanced Bios Features „ PnP/PCI ConfigurationTime Standard Cmos FeaturesIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Memory Floppy 3 Mode Support for Japan AreaDrive a Base MemoryFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Boot Up Floppy SeekFrame Buffer Size Password CheckInit Display First Onboard GPUIntegrated Peripherals SPPOn-Chip IDE Channel1 SATA-II 2 Secondary RAIDOn-Chip IDE Channel0 IDE1 Conductor CableOnboard Audio Function Onboard LAN Boot ROMParallel Port Mode Onboard LAN FunctionPME Event Wake Up Power Management SetupPower-On by Alarm Modem Ring OnPower On By Mouse Power On By KeyboardKB Power on Password AC Back FunctionPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status CPU Smart FAN Control Note Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsConnecting the Video Output Devices EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview How to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to 4 to flash the backup BIOS, too Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Before you begin SPP SCSI-0 Nvidia Mirror Step Save and exit Bios Setup GA-K8N51PVMT-9-RH Motherboard Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows SolutionsYES English Stereo Speakers Connection and Settings 5 2- / 4- / 6- / 8- Channel Audio Function IntroductionChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English Contact Us Taiwan HeadquartersGigabyte Global Service System