Gigabyte GA-K8N51PVM9-RH user manual Enter= Continue R=Repair F3=Exit

Page 77

Step 4:

When the next screen (Figure 19) appears, press ENTER to continue the SATA driver installation from the floppy disk.

Windows Setup

Setup will load support for the following mass storage device(s):

NVIDIA RAID CLASS DRIVER (required)

NVIDIA NForce Storage Controller (required)

*To specify additional SCSI adapters, CD-ROM drives, or special disk controllers for use with Windows, including those for which you have a device support disk from a mass storage device manufacturer, press S.

*If you do not have any device support disks from a mass storage device manufacturer, or do not want to specify additional mass storage devices for use with Windows, press ENTER.

S=Specify Additional Device ENTER=Continue F3=Exit

Figure 19

After the SATA controller driver installation is completed, you should see a screen similar to that below. You can proceed with the Windows 2000/XP installation now.

WindowsXP Professional Setup

Welcome to Setup.

This port of the Setup program prepares Microsoft(R)

Windows (R) XP to run on your computer.

To set up Windows XP now, press ENTER.

To repair a Windows XP installation using

Recovery Console, press R.

To quit Setup without installing Windows XP, press F3.

Enter= Continue R=Repair

F3=Exit

 

Figure 20

English

- 77 -

Appendix

Image 77
Contents GA-K8N51PVM9-RH-NV Motherboard Product Manual Classification CopyrightTable of Contents Drivers Installation Optional Accessories GA-K8N51PVM9-RH-NV Motherboard Layout Block Diagram Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerFeature Summary 4M bit flash ROM Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power ConnectorIDE1 / IDE2 IDE Connector Pwrled Fpanel Front Panel Jumper Cdin CD In Connector Faudio Front Audio Panel ConnectorTpmclr Tpmphysicalpresence USB1 / FUSB2 Front USB ConnectorSpdifio Spdif In/Out Coma Coma ConnectorCI Chassis Intrusion, Case Open Clrcmos Clear CmosEnglish Main Menu Status Page Setup Menu / Option Page Setup MenuF12 Boot Menu Main Menu For example Bios Ver. F3d„ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationTime Standard Cmos FeaturesIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave IDE Channel 2/3/4/5 MasterDrive a Floppy 3 Mode Support for Japan AreaMemory Base MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Boot Up Floppy SeekInit Display First Password CheckFrame Buffer Size Onboard GPUSPP Integrated PeripheralsOn-Chip IDE Channel0 SATA-II 2 Secondary RAIDOn-Chip IDE Channel1 IDE1 Conductor CableParallel Port Mode Onboard LAN Boot ROMOnboard Audio Function Onboard LAN FunctionPower-On by Alarm Power Management SetupPME Event Wake Up Modem Ring OnKB Power on Password Power On By KeyboardPower On By Mouse AC Back FunctionPCI 1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status System Smart FAN Control CPU Smart FAN Control NoteCPU Frequency Frequency/Voltage ControlPcie Clock K8 CPU Clock RatioTPM Control Trusted Platform Module Control Security Chip ConfigurationLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationDual-Monitor Setup Horizontal Span Mode Clone ModeVertical Span Mode Dual View ModeEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Press Y on your keyboard to save and exit FlashTMutility bar Exploring the Q-FlashTMutility screenCongratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM UtilityEnglish Installing Sata hard drives in your computer SPP Nvidia Mirror Step Save and exit Bios Setup GA-K8N51PVM9-RH-NV Motherboard Configuring RAID set in RAID Bios YES Nvidia Making a Sata Driver Disk Cd bootdrv MenuInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Solutions Configuring a bootable RAID array with Microsoft Windows1NO .0.M GA-K8N51PVM9-RH-NV Motherboard 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsEnglish Channel Audio Setup English English Sound Effect Configuration Introduction of the TPM Security Solution Troubleshooting English English English English English English English Taiwan Headquarters Contact UsGigabyte Global Service System