Gigabyte user manual GA-K8N51PVM9-RH-NV Motherboard

Page 80

English

Step 5:

Install the NVIDIA nForce Driver Package while in Windows 2000 and reboot the system. Go to START> Programs>Nvidia Corporation and select NVRAID manager. You should see the single disk RAID array (in striping mode) that was created from the boot disk. Select the single boot disk RAID Array by clicking on it. Select Convert Array under the System Tasks and select Next following the instructions. Select the desired type of RAID array you want to convert and then select Next. You are prompted to select the desired Free Disk(s) to add to the bootable RAID array. Press Finish then NVRAID will start converting the single disk RAID array into a multi-disk RAID array in a bootable format.

Note: Conversion may take 1~2 hours depending on disk size.

Solutions 2:

Users must create a combination installation CD that includes Windows 2000 and Service Pack 3 or Service Pack 4 fixes integrated in. To create the combination installation CD, refer to the following website: http://www.microsoft.com/windows2000/downloads/servicepacks/sp4/HFdeploy.htm

Note: If users choose not to install Windows 2000 Service Pack 3 or 4, RAID is still supported on Windows 2000. However, users will not be able to create a bootable RAID volume.

GA-K8N51PVM9-RH-NV Motherboard

- 80 -

Image 80
Contents GA-K8N51PVM9-RH-NV Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation Optional Accessories GA-K8N51PVM9-RH-NV Motherboard Layout Block Diagram Considerations Prior to Installation Installation NoticesInstances of Non-Warranty Preparing Your ComputerFeature Summary 4M bit flash ROM Installation of the CPU and CPU Cooler Installation of the CPUInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V / ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector Pwrled Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorUSB1 / FUSB2 Front USB Connector Tpmclr TpmphysicalpresenceComa Coma Connector Spdifio Spdif In/OutClrcmos Clear Cmos CI Chassis Intrusion, Case OpenEnglish Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. F3d F12 Boot Menu„ Standard Cmos Features „ Advanced Bios Features„ Power Management Setup „ PnP/PCI ConfigurationStandard Cmos Features TimeIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave IDE Channel 2/3/4/5 MasterFloppy 3 Mode Support for Japan Area Drive aMemory Base MemoryAdvanced Bios Features Hard Disk Boot PriorityFirst / Second / Third Boot Device Boot Up Floppy SeekPassword Check Init Display FirstFrame Buffer Size Onboard GPUIntegrated Peripherals SPPSATA-II 2 Secondary RAID On-Chip IDE Channel0On-Chip IDE Channel1 IDE1 Conductor CableOnboard LAN Boot ROM Parallel Port ModeOnboard Audio Function Onboard LAN FunctionPower Management Setup Power-On by AlarmPME Event Wake Up Modem Ring OnPower On By Keyboard KB Power on PasswordPower On By Mouse AC Back FunctionPnP/PCI Configurations PCI 1 IRQ AssignmentPC Health Status CPU Smart FAN Control Note System Smart FAN ControlFrequency/Voltage Control CPU FrequencyPcie Clock K8 CPU Clock RatioSecurity Chip Configuration TPM Control Trusted Platform Module ControlLoad Fail-Safe Defaults Load Optimized DefaultsSet Supervisor/User Password Save & Exit Setup Exit Without SavingDrivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsDual-Monitor Setup Clone Mode Horizontal Span ModeVertical Span Mode Dual View ModeEnglish User Interface Overview Unique Software UtilitiesEasyTune 5 Introduction System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Limitations Main Screen of Xpress Recovery2Precautions Before You Begin Flash Bios Method IntroductionMethod 1 Q-FlashTMUtility Exploring the Q-FlashTM / Dual Bios utility screen Task menu for Dual Bios utilityEntering the Q-FlashTMutility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to 4 to flash the backup BIOS, too Press Y on your keyboard to save and exit Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish Installing Sata hard drives in your computer SPP Nvidia Mirror Step Save and exit Bios Setup GA-K8N51PVM9-RH-NV Motherboard Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation ENTER=Select F3=Exit Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows Solutions1NO .0.M GA-K8N51PVM9-RH-NV Motherboard 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsEnglish Channel Audio Setup English English Sound Effect Configuration Introduction of the TPM Security Solution Troubleshooting English English English English English English English Contact Us Taiwan HeadquartersGigabyte Global Service System