Gigabyte GA-K8NF-9 user manual Feature Summary, Lan

Page 10

English

1-2	Feature Summary

CPU			Socket 939 for AMD SempronTM / AlthlonTM 64 / AlthlonTM 64 FX /
			AlthlonTM 64 X2 Dual-Core processor (K8)
		Supports core frequencies in excess of 3000+ and faster
System Bus			1600MHz
Chipset			nVIDIA® nForce4(-4X) chipset
LAN			Onboard VITESSE 8201 phy (10/100/1000Mbit)
Audio			Onboard Realtek ALC850 chip
		Supports 2 / 4 / 6/ 8 channel audio
		Supports Jack Sensing (Connector Sensing)
		Supports SPDIF In/Out connection
		Supports CD In connection
Storage			nVIDIA® nForce4(-4X) chipset
			- 1 FDD connector, allowing connection of 2 FDD devices
			- 2 IDE connectors (IDE1, IDE2) with UDMA 33/ATA 66/ATA 100/ATA 133
			suppport, allowing connection of 4 IDE devices
			- 4 SATA connectors (SATAII0_1, SATAII2_3), allowing connection of 4
			SATA devices
			- Supports data striping (RAID 0), mirroring (RAID 1),
			striping + mirroring (RAID 0+1) for Serial ATA
O.S Support			Microsoft Windows 2000/XP
Memory			4 DDR DIMM memory slots (supports up to 4GB memory) (Note 1)
		Supports dual channel DDR 400/333/266/200 DIMMs
		Supports 2.5V DDR DIMMs

Expanstion Slots			1 PCI Express x 16 slot
		2 PCI Express x 1 slots
			3 PCI slots
Internal Connectors			1 24-pin ATX power connector
		1 4-pin ATX 12V power connector
			1 floppy connector
			2 IDE connectors
			4 SATA 1.5Gb/s connectors
		1 CPU fan connector
		1 system fan connector
		1 front panel connector

1 front audio connector 1 CD In connector

3 USB 2.0/1.1 connectors for additional 6 USB 2.0/1.1 ports by cables 2 IEEE1394b connectors for 3 additional IEEE1394 ports by cables

1 power LED connector

GA-K8NF-9(rev. 2.2) Motherboard

- 10 -

Image 10

Contents GA-K8NF-9rev Motherboard Copyright Product Manual ClassificationTable of Contents Drivers Installation GA-K8NF-9rev .2 Motherboard Layout Block Diagram Page Instances of Non-Warranty Considerations Prior to InstallationInstallation Notices Preparing Your ComputerFeature Summary LAN4Mbit flash ROM Installation of the CPU and Fan Heat Sink Installation of the CPUInstallation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction Side Speaker OutATX12V/ATX Power Connector Cpufan / Sysfan Cooler Fan Power Connector FDD FDD ConnectorIDE1 / IDE2 IDE Connector Pwrled Fpanel Front Panel Jumper Faudio Front Audio Panel Connector Cdin CD In ConnectorUSB1 / FUSB2 / FUSB3 Front USB Connector 14 F11394 / F21394 Front Ieee 1394 ConnectorsClrcmos Clear Cmos Status Page Setup Menu / Option Page Setup Menu Main MenuMain Menu For example Bios Ver. D1 F12 For Boot Menu„ Power Management Setup „ Standard Cmos Features„ Advanced Bios Features „ PnP/PCI ConfigurationIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave TimeIDE Channel 2/3/4/5 Master Drive a / Drive B Floppy 3 Mode Support for Japan AreaHalt on First / Second / Third Boot Device Hard Disk Boot PriorityBoot Up Floppy Seek Password Check Init Display FirstOn-Chip IDE Channel0 IDE DMA transfer accessIntegrated Peripherals On-Chip IDE Channel1On-Chip MAC Lan controlled by Vitesse 8201 phy On-Chip LAN Boot ROMIDE Prefetch Mode NV IDE/SATA RAID functionOnboard Serial Port Parallel Port ModeECP Mode Use DMA Onboard Parallel PortPower Management Setup KB Power on Password Power On by MousePower On by Keyboard AC Back FunctionPnP/PCI Configurations Current VoltageV Vcore / DDR25V / +3.3V / +12V Current CPU TemperaturePC Health Status Current CPU/SYSTEM FAN Speed RPMCPU FAN Fail Warning CPU Warning TemperatureTemp of FAN turn off Default temperature 0oC CPU Smart FAN Control NoteTemp Limit of High Speed Default temperature 60oC Temp Limit of Low Speed Default temperature 20oCTemp Limit of Mid Speed Default temperature 50oC Temp of full FAN Speed Default temperature 70oCK8 CPU Clock Ratio HT Frequency RatioCPU Frequency Current DDR speedHT-Link voltage control Chipset core PCI-E voltageDDR voltage control Top Performance Set Supervisor/User Password Save & Exit Setup Exit Without SavingEnglish Drivers Installation Install Chipset DriversSoftware Application Software InformationHardware Information Contact UsEnglish EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview How to use the Xpress Recovery2 Xpress Recovery2 IntroductionSystem requirements Precautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Entering the Q-FlashTMutility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Task menu for Q-Flash utilityUsing the Q-FlashTMutility StepsYou can repeat to Part Two Exploring the Q-FlashTMutility screen FlashTMutility barCongratulation!! You have updated Bios successfully Method 2 @BIOSTM Utility Methods and stepsEnglish To configure Sata hard drives, follow the steps below Configuring Sata Hard DrivesInstall Sata hard drives in your system Disabled NV Sata 1 Secondary Appendix Step Save and exit Bios Setup GA-K8NF-9rev .2 Motherboard Configuring RAID set in RAID Bios YES Nvidia Cd bootdrv Menu Making a Sata Driver DiskInstalling Sata controller driver during OS installation NForce Storage Controller Enter= Continue R=Repair F3=Exit Configuring a bootable RAID array with Microsoft Windows SolutionsYES English Stereo Speakers Connection and Settings Introduction of audio connectors5 2- / 4- / 6- / 8- Channel Audio Function Introduction Channel Audio Setup English Step Troubleshooting AMI Bios Beep CodesEnglish English English Contact Us Taiwan HeadquartersChina Shanghai