Gigabyte GA-8S661GXMP Drive a / Drive B, Floppy 3 Mode Support for Japan Area, Halt on, Memory

Page 31

Drive A / Drive B

The category identifies the types of floppy disk drive A or drive B that has been installed in the computer.

None

No floppy drive installed

360K, 5.25"

5.25 inch PC-type standard drive; 360K byte capacity.

1.2M, 5.25"

5.25 inch AT-type high-density drive; 1.2M byte capacity

 

(3.5 inch when 3 Mode is Enabled).

720K, 3.5"

3.5 inch double-sided drive; 720K byte capacity

1.44M, 3.5"

3.5

inch double-sided drive; 1.44M byte capacity. (Default value)

2.88M, 3.5"

3.5

inch double-sided drive; 2.88M byte capacity.

Floppy 3 Mode Support (for Japan Area)

Disabled

Normal Floppy Drive. (Default value)

Drive A

Drive A is 3 mode Floppy Drive.

Drive B

Drive B is 3 mode Floppy Drive.

Both

Drive A & B are 3 mode Floppy Drives.

Halt on

The category determines whether the computer will stop if an error is detected during power-up.

No Errors

The system boot will not stop for any error that may be detected and you

 

will be prompted.

All Errors

Whenever the BIOS detects a non-fatal error the system will be stopped.

All, But Keyboard

The system boot will not stop for a keyboard error; it will stop for all other

 

errors. (Default value)

All, But Diskette

The system boot will not stop for a disk error; it will stop for all other errors.

All, But Disk/Key

The system boot will not stop for a keyboard or disk error; it will stop for all

 

other errors.

Memory

The category is display-only and is determined by POST (Power On Self Test) of the BIOS.

Base Memory

The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system.

The value of the base memory is typically 512K for systems with 512K memory installed on

the motherboard, or 640K for systems with 640K or more memory installed on the motherboard.

Extended Memory

The BIOS determines how much extended memory is present during the POST.

This is the amount of memory located above 1 MB in the CPU's memory address map.

Total Memory

This item displays the memory size that used.

English

- 31 -

BIOS Setup

Image 31
Contents GA-8S661GXMP-C GA-8S661GXMP Product Manual Classification CopyrightTable of Contents Drivers Installation GA-8S661GXMP-C Motherboard Layout Block Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyFeature Summary Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Pin One IndicatorInstallation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector IDE1/IDE2 IDE Connector Cpufan / Sysfan Cooler Fan Power ConnectorFaudio Front Audio Panel Connector FDD FDD ConnectorFpanel Front Panel Connector Surcen Cdin CD in ConnectorSpdifio Spdif In/ Out 12 F1USB / F2USB Front USB ConnectorsClrcmos Clear Cmos CI Chassis Intrusion, Case OpenPwrled Comb Comb ConnectorBAT Battery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E2 „ Save & Exit Setup „ Set User Password„ Exit Without Saving Time Standard Cmos FeaturesIDE Channel 0 Master, Slave /IDE Channel 1 Master, Slave Memory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Limit Cpuid Max. to Boot Up Floppy SeekPassword Check CPU Hyper-ThreadingECP Integrated PeripheralsUSB Controller Parallel Port ModeECP Mode Use DMA Onboard LAN deviceIRQ 3-7, 9-15, NMI Power Management SetupModemRingOn Power LED in S1 State Power On By KeyboardPower On By Mouse Resume by AlarmPCI 1 IRQ Assignment PnP/PCI ConfigurationsCurrent VoltageV Vcore / DDR 2.5V / +3.3V / +12V Current CPU TemperaturePC Health Status Case OpenedMB Intelligent Tweaker M.I.T AGP Clock MHz CPU Clock MHzDram Clock MHz AGP/PCI Clock ControlLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Unique Software UtilityPrecautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Bios Flash Method IntroductionBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Press Y on your keyboard to save and exit English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish 3 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Jack-Sensing Introuction Introduction of audio connectorsManual setting Troubleshooting English English Taiwan Headquarters Contact UsChina Shanghai