Gigabyte GA-8S661GXMP user manual Block Diagram

Page 7

Block Diagram

AGP 4X/8X

AGPCLK (66MHz)

3 PCI

VGA Port

Pentium 4					CPUCLK+/- (100/133MHz)
Socket 478					CPUCLK+/- (100/133MHz)
Socket 478
CPU

	Host							266/333/400MHz
	Interface							266/333/400MHz
	Interface
									DDR RAM
									DDR RAM
SiS 661GX
SiS 661GX					HCLK+/- (100/133/200MHz)

133MHz 33 MHz 14.318 MHz

48 MHz

PCICLK (33MHz)



					Link
					Link
ICS1883*					AC97


				AC97
RJ45*			CODEC
RJ45*			CODEC



			MIC	LINE-IN LINE-OUT

SiS 964L

LPC BUS

8 USB ATA33/66/100/

Ports 133 IDE

Channels

IT8705AF

24 MHz

33 MHz

PS/2

KB/Mouse

BIOS

Floppy

LPT Port

COM

Ports

"*" Only for GA-8S661GXMP

- 7 -

Image 7

Contents GA-8S661GXMP-C GA-8S661GXMP Product Manual Classification CopyrightTable of Contents Drivers Installation GA-8S661GXMP-C Motherboard Layout Block Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyFeature Summary Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Pin One IndicatorInstallation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector IDE1/IDE2 IDE Connector Cpufan / Sysfan Cooler Fan Power ConnectorFaudio Front Audio Panel Connector FDD FDD ConnectorFpanel Front Panel Connector Surcen Cdin CD in ConnectorSpdifio Spdif In/ Out 12 F1USB / F2USB Front USB ConnectorsClrcmos Clear Cmos CI Chassis Intrusion, Case OpenPwrled Comb Comb ConnectorBAT Battery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E2 „ Save & Exit Setup „ Set User Password„ Exit Without Saving Time Standard Cmos FeaturesIDE Channel 0 Master, Slave /IDE Channel 1 Master, Slave Memory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Limit Cpuid Max. to Boot Up Floppy SeekPassword Check CPU Hyper-ThreadingECP Integrated PeripheralsUSB Controller Parallel Port ModeECP Mode Use DMA Onboard LAN deviceIRQ 3-7, 9-15, NMI Power Management SetupModemRingOn Power LED in S1 State Power On By KeyboardPower On By Mouse Resume by AlarmPCI 1 IRQ Assignment PnP/PCI ConfigurationsCurrent VoltageV Vcore / DDR 2.5V / +3.3V / +12V Current CPU TemperaturePC Health Status Case OpenedMB Intelligent Tweaker M.I.T AGP Clock MHz CPU Clock MHzDram Clock MHz AGP/PCI Clock ControlLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Unique Software UtilityPrecautions Main Screen of Xpress Recovery2Limitations Method 1 Q-FlashTMUtility Bios Flash Method IntroductionBefore You Begin Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Press Y on your keyboard to save and exit English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish 3 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Jack-Sensing Introuction Introduction of audio connectorsManual setting Troubleshooting English English Taiwan Headquarters Contact UsChina Shanghai