Gigabyte GA-8S661GXMP Onboard LAN device, USB Controller, USB Legacy Support, Onboard Serial Port

Page 35

Onboard LAN device*

Enabled	Enable Onboard LAN device function. (Default value)
Disabled	Disable this function.

USB Controller

Enabled	Enable USB Controller. (Default value)
Disabled	Disable USB Controller.

USB Legacy Support

Enabled	Enable USB Legacy Support.
Disabled	Disable USB Legacy Support. (Default value)

Onboard Serial Port 1

Auto	BIOS will automatically setup the Serial port 1 address.
3F8/IRQ4	Enable onboard Serial port 1 and address is 3F8/IRQ4. (Default value)
2F8/IRQ3	Enable onboard Serial port 1 and address is 2F8/IRQ3.
3E8/IRQ4	Enable onboard Serial port 1 and address is 3E8/IRQ4.
2E8/IRQ3	Enable onboard Serial port 1 and address is 2E8/IRQ3.
Disabled	Disable onboard Serial port 1.

Onboard Serial Port 2

Auto	BIOS will automatically set up the Serial port 2 address.
3F8/IRQ4	Enable onboard Serial port 2 and address is 3F8/IRQ4.
2F8/IRQ3	Enable onboard Serial port 2 and address is 2F8/IRQ3. (Default value)
3E8/IRQ4	Enable onboard Serial port 2 and address is 3E8/IRQ4.
2E8/IRQ3	Enable onboard Serial port 2 and address is 2E8/IRQ3.
Disabled	Disable onboard Serial port 2.

Onboard Parallel Port

Disabled	Disable onboard LPT port.
378/IRQ7	Enable onboard LPT port and address is 378/IRQ7. (Default value)
278/IRQ5	Enable onboard LPT port and address is 278/IRQ5.
3BC/IRQ7	Enable onboard LPT port and address is 3BC/IRQ7.

Parallel Port Mode

SPP	Use Parallel port as Standard Parallel Port.
EPP	Use Parallel port as Enhanced Parallel Port.
ECP	Use Parallel port as Extended Capabilities Port. (Default value)
ECP+EPP	Use Parallel port as ECP & EPP mode.

ECP Mode Use DMA

This option is available only when Parallel Port Mode is set to ECP or ECP+EPP.

3	Set ECP Mode Use DMA to 3. (Default value)
1	Set ECP Mode Use DMA to 1.

"*" Only for GA-8S661GXMP

- 35 -

BIOS Setup

English

Image 35

Contents GA-8S661GXMP-C GA-8S661GXMP Product Manual Classification CopyrightTable of Contents Drivers Installation GA-8S661GXMP-C Motherboard Layout Block Diagram Page Preparing Your Computer Considerations Prior to InstallationInstallation Notices Instances of Non-WarrantyFeature Summary Installation of the CPU Installation of the CPU and HeatsinkInstallation of the Heatsink Pin One IndicatorInstallation of Memory Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector IDE1/IDE2 IDE Connector Cpufan / Sysfan Cooler Fan Power ConnectorFaudio Front Audio Panel Connector FDD FDD ConnectorFpanel Front Panel Connector Surcen Cdin CD in ConnectorSpdifio Spdif In/ Out 12 F1USB / F2USB Front USB ConnectorsClrcmos Clear Cmos CI Chassis Intrusion, Case OpenPwrled Comb Comb ConnectorBAT Battery English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example Bios Ver. E2 „ Exit Without Saving „ Set User Password„ Save & Exit Setup IDE Channel 0 Master, Slave /IDE Channel 1 Master, Slave Standard Cmos FeaturesTime Memory Floppy 3 Mode Support for Japan AreaDrive a / Drive B Halt onFirst / Second / Third Boot Device Advanced Bios FeaturesHard Disk Boot Priority Limit Cpuid Max. to Boot Up Floppy SeekPassword Check CPU Hyper-ThreadingECP Integrated PeripheralsUSB Controller Parallel Port ModeECP Mode Use DMA Onboard LAN deviceModemRingOn Power Management SetupIRQ 3-7, 9-15, NMI Power LED in S1 State Power On By KeyboardPower On By Mouse Resume by AlarmPCI 1 IRQ Assignment PnP/PCI ConfigurationsCurrent VoltageV Vcore / DDR 2.5V / +3.3V / +12V Current CPU TemperaturePC Health Status Case OpenedMB Intelligent Tweaker M.I.T AGP Clock MHz CPU Clock MHzDram Clock MHz AGP/PCI Clock ControlLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Drivers InstallationSoftware Information Software ApplicationContact Us Hardware InformationEnglish System requirements Xpress Recovery2 IntroductionHow to use the Xpress Recovery2 Unique Software UtilityLimitations Main Screen of Xpress Recovery2Precautions Before You Begin Bios Flash Method IntroductionMethod 1 Q-FlashTMUtility Task menu for Q-Flash utility Exploring the Q-FlashTM / Dual Bios utility screenTask menu for Dual Bios utility Entering the Q-FlashTMutilitySteps Using the Q-FlashTMutilityYou can repeat to 4 to flash the backup BIOS, too Press Y on your keyboard to save and exit English Exploring the Q-FlashTMutility screenBios file becomes F4 after updating Congratulation!! You have updated Bios successfullyMethods and steps Method 2 @BIOSTM UtilityEnglish 3 2 / 4 / 6 Channel Audio Function Introduction Channel Audio SetupChannel Analog Audio Output Mode Basic 6 Channel Analog Audio Output Mode English Basic & Advanced 6 Channel Analog Audio Output Mode Notes Spdif Output Device Optional Device Jack-Sensing Introuction Introduction of audio connectorsManual setting Troubleshooting English English Taiwan Headquarters Contact UsChina Shanghai