Tripp Lite none owner manual Basic Operation Front Panel, Equipment on during a self-test

Page 3

Quick Installation (Continued)

STEP 3: Plug your equipment into the UPS: Select outlets will provide battery backup and surge pro- tection; plug your computer, monitor and other critical devices here.* Select outlets will provide surge protection only; plug your printer and other nonessential devices here. (See Basic Operation Section.)

*Your UPS is designed to support electronic equipment only. You will overload the UPS if the total VA ratings for all the equipment you connect to the Battery Backup Protected/Surge Protected outlets exceeds the UPS’s Output Capacity. To find your equipment’s VA ratings, look on their nameplates. If the equipment is listed in amps, multiply the number of amps by 120 to determine VA. (Example: 1 amp × 120 = 120 VA). If you are unsure if you have overloaded the Battery Backup Protected/Surge Protected outlets, run a self-test (see “MUTE/TEST” Button description).

CAUTION: The UPS must be plugged into a live AC outlet and turned on for 24 hours after initial installation to fully charge the UPS's internal battery. Your connected equipment will receive utili- ty-supplied AC power (if present) immediately after the UPS is plugged in and turned on; howev- er, your connected equipment may not receive full battery backup in the event of a blackout or severe brownout until the UPS's internal battery is fully charged.

Basic Operation (Front Panel)

1“ON/OFF” Button

•To turn the UPS on: Press and hold the ON/OFF Button for one second.* If utility power is absent, pressing the Button will “cold-start” the UPS, i.e. turn it on and supply power from its battery.**

•To turn the UPS off: Press and hold the ON/OFF Button for one second.*

 

The UPS will be turned completely off (deactivated).

1

 

* The alarm will beep once briefly after one second has passed. ** Runtime will be proportionate to the

ON/OFF Button

UPS battery's level of charge.

2 “MUTE/TEST” Button

 

•To Silence (or “Mute”) UPS Alarms: briefly press and release the

 

MUTE/TEST button. Note: continuous alarms (warning you to shut down

 

connected equipment immediately) cannot be silenced.

 

•To Run a Self-Test: with your UPS plugged in and turned on, press and

 

hold the MUTE/TEST button for two seconds. Continue holding the button

2

until the alarm beeps several times and the UPS performs a self-test.

See “Results of a Self-Test” below. Note: you can leave connected

MUTE/TEST Button

 

equipment on during a self-test.

 

CAUTION! Do not unplug your UPS to test its battery. This will remove safe electrical grounding and may introduce a damaging surge into your network connections.

Results of a Self-Test: The test will last approximately 10 seconds as the UPS switches to battery to test its load capacity and charge. All LCD Display icons will be illuminated and the UPS alarm will sound.

•If the “FAULT” icon remains lit and the alarm continues to sound after the test, the battery- supported outlets are overloaded. To clear the overload, unplug some of your equipment from the battery-supported outlets and repeat the self-test until the “FAULT” icon is no longer lit and the alarm is no longer sounding. Note: The alarm beeps once per minute.

CAUTION!Any overload that is not corrected by the userimmediately following a self-test may cause the UPS to shut down and cease supplying output power in the event of a blackout or brownout.

•If the “REPLACE” icon remains lit and the alarm continues to sound after the test, the UPS batteries need to be recharged or replaced. Allow the UPS to recharge continuously for 24 hours, and repeat the self-test. If the icon continues to illuminate after repeated self tests, contact Tripp Lite for service. Battery replacement should only be performed by qualified service personnel. If the UPS requires battery replacement, Tripp Lite offers a complete line of replacement batteries at www.tripplite.com. Note: The alarm beeps once per minute.

3

Image 3
Contents Digital UPS Systems Quick Installation Important Safety InstructionsEquipment on during a self-test Basic Operation Front PanelPosition. To rotate the LCD Status Screen insert a small Basic Operation Rear Panel Warranty Registration Storage & ServiceSistemas UPS digitales Instalación rápida Instrucciones de seguridad importantesBotón ON/OFF Encendido/Apagado Operación básica Panel frontalOperación básica Panel frontal-continúa Operación básica Panel posteriorNota sobre el rotulado Almacenamiento y ServicioAlmacenamiento ServicioSystèmes ’onduleurs numériques Consignes de sécurité importantes Installation rapideBouton ON/OFF Bouton MUTE/TEST Fonctionnement de base panneau avantFonctionnement de base panneau arrière Fonctionnement de base panneau avant-suiteEntreposage et entretien EntreposageEntretien