Tripp Lite AG-0020, AG-0022, AG-0021 owner manual Buttons Front Panel, ON/OFF/STANDBY Button

Page 5

201112134 93-3152.qxd 1/18/2012 2:16 PM Page 5

Basic Operation

Buttons (Front Panel)

“ON/OFF/STANDBY” Button

•To turn the UPS ON: with the UPS plugged into a live AC wall outlet*, press and hold the “ON/OFF/STANDBY” button for one second.** Release the button. If utility power is absent, you can “cold-start” the UPS (i.e.: turn it ON and supply power for a limited time from its batteries***) by pressing and holding the “ON/OFF/STANDBY” button for one second.**

•To turn the UPS OFF: with the UPS ON and receiving utility power, press and hold the “ON/OFF/STANDBY” button for one second.** Then unplug the UPS from the wall outlet. The UPS will be completely OFF.

*After you plug the UPS into a live AC outlet, the UPS (in ”Standby” mode) will automatically charge its batteries, but will not supply power to its outlets until it is turned ON. ** The alarm will beep once briefly after the indicated interval has passed. *** If fully charged.

“MUTE/TEST” Button

To Silence (or “Mute”) UPS Alarms: briefly press and release the MUTE/TEST button.*

To Run a Self-Test:with your UPS plugged in and turned ON, press and hold the MUTE/TEST button. Continue holding the button until the alarm beeps several times and the UPS performs a self test. See “Results of a Self-Test” below. Note: you can leave connected equipment on during a self-test. Your UPS, however, will not perform a self-test if the UPS is not turned on (see “ON/OFF/STANDBY” Button description).

CAUTION! Do not unplug your UPS to test its batteries. This will remove safe electrical grounding and may introduce a damaging surge into your network connections.

Results of a Self-Test:The test will last approximately 10 seconds as the

UPS switches to battery to test its load capacity and battery charge.

•If the “OUTPUT LOAD LEVEL” LED remains lit red and the alarm continues to sound after the test, the UPS’s outlets are overloaded. To clear the overload, unplug some of your equipment and run the self-test repeatedly until the “OUTPUT LOAD LEVEL” LED is no longer lit red and the alarm is no longer sounding.

CAUTION! Any overload that is not corrected by the user immediately following a self-test may cause the UPS to shut down and cease supplying output power in the event of a blackout or brownout.

•If the “BATTERY WARNING” LED remains lit and the alarm continues to sound after the test, the UPS batteries need to be recharged or replaced. Allow the UPS to recharge continuously for 12 hours, and repeat the self-test. If the LED remains lit, contact Tripp Lite for service. If your UPS requires battery replacement, visit www.tripplite.com/support/battery/index.cfm to locate the specific Tripp Lite replacement battery for your UPS.

* The alarm will beep once briefly after the indicated interval has passed.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Agency Models AG-0020, AG-0021, AG-0022 Intelligent, Line-Interactive UPS SystemBattery Warnings Important Safety InstructionsUPS Location Warnings UPS Connection WarningsTurn the UPS on USB and RS-232 Serial Communications ON/OFF/STANDBY Button Buttons Front PanelIndicator Lights Front Panel Other UPS Features Rear Panel Carefully pull the front panel away from the UPS Modelos de Agencia AG-0020, AG-0021, AG-0022 Sistema de UPS, Inteligentes y Interactivos en LíneaAdvertencias sobre la ubicación del UPS Instrucciones de seguridad importantesAdvertencias sobre la conexión del UPS Advertencias sobre la conexión de equiposEncienda el UPS Teléfono/gatos de conexión de red Comunicaciones USB y serie RS-232 Todos los modelosBotón ON/OFF/STANDBY Encendido/Apagado/Reserva Botones Panel frontalLuces indicadoras Panel frontal Operación básica continúaOtras funciones del UPS Panel posterior Servicio técnico Reassemble UPSAlmacenamiento Modèles dagences AG-0020, AG-0021, AG-0022 Systémes UPS intelligent, en attente activeDirectives de sécurité importantes Mises en garde Emplacement de lUPSMises en garde Connexions de lUPS Mises en garde Connexion déquipementSMX750SLT Téléphoner/Crics de Protection de Réseau Bouton ON/OFF/STANDBY Marche/Arrêt/Attente Boutons Panneau avantVoyants indicateurs Panneau avant Fonctionnement de base, suiteAutres caractéristiques de lUPS panneau arrière Entretien Réassemblez lUPSEntreposage Agenturmodelle AG-0020, AG-0021, AG-0022 Intelligentes USV-System mit aktivem Standby-ModusWarnhinweis zum Aufstellungsort der USV Wichtige SicherheitsinstruktionenWarnhinweise zum Anschluss der USV Warnung zum Anschluss von GerätenSchalten Sie die USV ein USB und RS-232 serielle Kommunikationsanschlüsse Taste „ON/OFF/STANDBY EIN/AUS/STABNDBY Tasten Vorderes BedienfeldAnzeigeleuchten Vorderes Bedienfeld Grundbetrieb FortsetzungSonstige USV-Funktionsmerkmale Rückseite Hinweis auf der Etikettierung ServiceLagerung         

AG-0020, AG-0021, AG-0022 specifications

Tripp Lite, a leader in power protection and connectivity solutions, offers a range of high-quality surge protectors, including the AG-0022, AG-0020, and AG-0021 models. These surge suppressors are designed to meet the demands of modern electronics, providing essential protection against surges, spikes, and electrical noise that can damage devices and disrupt performance.

The Tripp Lite AG-0022 is a robust surge protector featuring advanced technology that safeguards multiple devices simultaneously. It boasts a high joule rating, which indicates its ability to absorb significant energy surges. The model includes multiple outlets, allowing users to connect several devices while ensuring they are all shielded from potential damage. With a built-in circuit breaker to prevent overloads, users can have peace of mind knowing their devices are secure.

In contrast, the Tripp Lite AG-0020 is designed for users who require a lightweight, compact solution for their power needs. Perfect for workstations and home offices, this model emphasizes portability without compromising on protection. Its sleek design includes keyhole mounting slots for easy installation in various environments. Although smaller in size, the AG-0020 still features a solid joule rating and incorporates EMI/RFI noise filtering technology to enhance the performance of connected devices.

The AG-0021 model combines versatility with exceptional protection features. It is particularly well-suited for sensitive electronics such as computers, televisions, and audio equipment. The AG-0021 includes individual switches for each outlet, allowing users to control power to each device independently. This feature enables energy-saving practices, as users can turn off devices that are not in use. Like its counterparts, the AG-0021 is equipped with a high joule rating and advanced noise filtering technology.

All three models are equipped with diagnostics and LED indicators that provide users with real-time status updates on power and surge protection levels. Additionally, Tripp Lite employs durable materials that ensure longevity and reliability, making these surge protectors a valuable addition to any electronic setup. With their distinct features, the AG-0022, AG-0020, and AG-0021 cater to diverse needs, offering superior protection and enhancing the longevity of valuable electronics in every environment.
Top Page Image Contents