Installation, UPS Location | Tripp Lite 220/380, 230/400, 240/415V

Installation

UPS LOCATION

Move your UPS over short distances using its wheels. Stabilize the UPS by releasing the stabilizers on each side of the unit. NOTE: Do not stack the UPS System power module or external battery modules.

UPS POWER MODULE INPUT AND OUTPUT HARDWIRE CONNECTION

In addition to the instructions listed below, follow all warnings found in the Safety section prior to connection.

WIRING SELECTION

Choose appropriate cabling (rated VW-1, FT-1 or better) to connect your UPS Power Module to an AC power supply and your equipment.

UPS System Model	Wiring Size
20kVA	8 AWG / 8 mm2
30kVA	6 AWG / 14 mm2

Maximum Cable Length: 10 m (32.8 ft)

WIRING CONNECTION

Connect your wiring to the input and output terminal blocks located on the lower rear panel of your UPS (see figure below).

CAUTION!

Qualified personnel should follow all procedures prescribed by N.E.C. and other local codes for hardwiring devices to a utility source. Ensure that cables are fitted with cable sleeves and are secured by connector clamps. Tighten connections with a torque of not less than 35 inch-pounds. Observe the appropriate cable connection regulations [e.g. National Electrical Code (NEC) in the U.S.] at all times. Using cables of improper size may damage your equipment and cause fire hazards.

N2 T2 S2 R2

N1 R1 S1

NOTE: when shipped from the factory, bypass input and main input wires are connected.

UPS BATTERY MODULE HARDWIRE CONNECTION

In addition to the instructions listed below, follow all warnings found in the Safety section prior to connection.

WARNING!

Before attempting to connect the UPS Power Module to the UPS Battery Module, qualified personnel must remove all fuses from all

UPS Battery Modules.

CAUTION!

Make certain that your UPS Power Module and UPS Battery Module use the same DC voltage before connecting them. When connecting multiple Battery Modules to a single Power Module, the Battery Modules should be approximately the same age. Do not connect or disconnect Battery Modules while the Power Module is operating on battery power, due to the possibility of dangerous arcing.

The UPS Power Module will not start without a connection to a charged UPS Battery Module. If you plan to store your Battery Module(s) for an extended period of time, fully recharge its batteries every three months by connecting it for at least 12 hours to a UPS Power Module that is connected to AC input.

WIRING SELECTION

Choose appropriate cabling (rated VW-1, FT-1 or better) to connect your UPS Battery Module to your UPS Power Module.

UPS System Model	Wiring Size
20kVA	4 AWG / 22 mm2
30kVA	2 AWG / 38 mm2

Maximum Cable Length: 10 m (32.8 ft)

240/415V, 220/380, 230/400 specifications

Tripp Lite is a well-known manufacturer in the power management and connectivity solutions sector, and their products often cater to various power requirements across industries. Among their offerings are the Tripp Lite 230/400V, 220/380V, and 240/415V models, designed to provide high-quality power solutions for industrial and commercial applications.

One of the core features of these systems is the ability to handle different voltage requirements, making them highly versatile in various environments. The 230/400V model is particularly suitable for European and global standards, ensuring compatibility with a wide range of electrical systems. Meanwhile, the 220/380V and 240/415V variants provide additional flexibility for specialized applications, allowing users to seamlessly switch between different voltage levels while maintaining consistent performance.

The technology behind these models is rooted in advanced voltage regulation and surge protection. Each unit is equipped with superior surge protection features designed to safeguard connected equipment from power spikes, ensuring longevity and reliability. This is particularly important in industrial settings where machinery and sensitive electronics are often exposed to power fluctuations.

In terms of power distribution, these Tripp Lite models come with multiple output options to accommodate various devices simultaneously. The layout is designed for optimal space utilization, allowing users to maximize efficiency in tight environments. Additionally, many units are equipped with intelligent LCD displays, offering real-time monitoring of voltage, load, and runtime statistics. This feature empowers users to make informed decisions about their power management, enhancing overall operational efficiency.

Reliability is a key characteristic of Tripp Lite products, and these models are no exception. Built with high-quality components, they are rugged and durable, designed to withstand harsh conditions often found in industrial settings. Furthermore, their fanless designs minimize noise, making them suitable for use in environments where sound is a concern.

Another important aspect is scalability. Businesses can easily integrate these systems into their existing infrastructure and expand as necessary. With Tripp Lite's commitment to quality and performance, the 230/400, 220/380, and 240/415V models serve as reliable and efficient solutions for various power management needs across different sectors, from manufacturing to data centers. Their combination of advanced technology, robust design, and user-friendly features ensures they remain a popular choice in the industry.