C H A P T E R 4
Cisco 7200 Series and the
PA-4T+ Port Adapter
This chapter provides information on the
•
•
•
Installation Overview, page
Removing a Port Adapter, page
Installing a Port Adapter, page
Installation Overview
Figure 4-1 shows a PA-4T+ installed in port adapter slot 1 of the Cisco 7206. The PA-4T+ is used in Cisco 7200 series routers and can be installed in any of the available port adapter slots.
Figure 4-1 Cisco 7206 with a PA-4T+ Installed
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| TOKEN RING |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 6 |
| 5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ETHERNET 10BT |
| ENABLED |
|
|
|
|
|
|
|
|
| FAST ETHERNET |
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| MII | LINK | RJ45 |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 4 | |||||
| 3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| FAST SERIAL, | ENHANCED |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| EN |
|
|
|
|
|
|
|
|
| RX | TX | RX 4 | TX |
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| RX |
| TX | RX | TX | RX | TX |
| 2 | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||
1 |
|
|
|
|
|
|
|
|
|
|
|
| 0 |
|
|
| 1 | 2 |
|
| 3 |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
port | Cisco 7200 |
|
|
|
| SLOT | 1 |
| MII |
|
|
|
|
|
|
|
|
|
| FAST ETHERNET INPUT/OUTPUT CONTROLLER |
|
|
| |||
adapter |
|
|
|
|
| FE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| H9708 | ||||
Series |
|
|
|
|
|
|
|
|
|
|
|
|
| RJ |
|
|
|
|
|
|
|
| 0 | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| MII | RJ |
| RJ |
| PWR |
|
|
|
|
|
|
|
|
|
|
| ENABLED | PCMCIA | EJECT | SLOT | 0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
| EN |
| EN |
| LINK 1O | OK |
|
|
|
|
|
|
|
|
|
| ||||
Depending on your circumstances, you might need to install a new port adapter in a Cisco 7200 series router or replace a failed port adapter in the field. In either case, no tools are necessary; all port adapters available for the Cisco 7200 series connect directly to the router midplane and are locked into position by a port adapter lever. When removing and replacing a port adapter, you will need an antistatic mat onto which you can place a removed port adapter and an antistatic container into which you can place a failed port adapter for shipment back to the factory.
Note Cisco 7200 series routers support online insertion and removal (OIR); therefore, you do not have to power down Cisco 7200 series routers when removing and replacing a
Cisco 7200 Series and the
