Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems PA-4T manual Software and Hardware Requirements

Models: PA-4T

1 76

Download 76 pages 35.25 Kb

<>

Install Inverting the Clock Signal Telephone Wiring Guidelines Checking the Configuration VIP2 show interfaces Command Setting the Clock Rate Safety

Page 25

Software and Hardware Requirements

Note The minimum recommended VIP2 model is a VIP2-15.

Preparing for Installation 2-3

Page 24 Page 26

Image 25

Cisco Systems PA-4T manual Software and Hardware Requirements

Page 24 Page 26

Related pages 4E-2. Control Circuit Trouble Shooting for Teledyne EHE Technical Specifications for Falcon F110 LED Error Indications for Mitel 5604 Wartungsschema for Husqvarna 233RJ HOW to Create Custom Programs for NordicTrack NTTL11511 Rakenduste deinstallimine või keelamine for Samsung SM-T705NTSASEB Parts List Natural GAS for 85-1651-2 G51209 for Centro 3900 Error Code List for Mitsubishi Electronics FR-A700 Setting as wallpaper for Samsung SM-P6010ZKESER Wide Area Surface Cleaner for Karcher K 3.68 M What Ethernet connections are needed for IPTV setup with 2Wire 3800? See connection steps

Contents

Corporate Headquarters Copyright 1997-1999 Cisco Systems, Inc All rights reserved Port Adapter Overview Overview PA-4T Port Adapter-Faceplate View Router# show diag Synchronous Serial Overview Serial Interface Speciﬁcations PA-4T+ Receptacles and Cables Cables and Pinouts Serial Port Adapter Cables EIA/TIA-232 Connections EIA/TIA-449 Connections EIA-530 Connections PA-4T+ Port Adapter Cable Pinouts RTS/CTS CTS/RTS DSR/DTR DTR/DSR RTS CTS DSR SD+ Shield ground RTS/CTS CTS/RTS DSR/DTR DTR/DSR DCD/LL Rlsd LL/DCD LEDs on the PA-4T+-Horizontal Orientation LEDs LEDs Objectives Preface Related Documentation Document Organization Cisco Connection Online Documentation CD-ROM Tools and Parts Required Preparing for Installation Router Platform Recommended Minimum Cisco IOS Release Software and Hardware Requirements Software and Hardware Requirements Safety Warnings Safety Guidelines Electrical Equipment Guidelines Telephone Wiring Guidelines Preventing Electrostatic Discharge Damage FCC Class B Compliance FCC Class B Compliance FCC Class B Compliance VIP2 and the PA-4T+ Port Adapter Installation Overview VIP2-15 or VIP2-40 with a PA-4T+ in Port Adapter Slot Removing a Port Adapter Location of Port Adapter Screw-Partial Port Adapter View Installing a Port Adapter Aligning a Port Adapter in a Port Adapter Slot H3152 Cisco 7200 Series PA-4T+ Port Adapter Cisco 7206 with a PA-4T+ Installed Port adapter Handle Lever unlocked Position Handling a Port Adapter Placing the Port Adapter Lever in the Locked Position-Cisco Cisco uBR7200 Series and the PA-4T+ Port Adapter Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Placing the Port Adapter Lever in the Locked Position Installing a Port Adapter Cisco 7120 Series Router-Port Adapter Slot 3 Location Cisco 7100 Series PA-4T+ Port Adapter Cisco 7140 Series Router-Port Adapter Slot 4 Location Installing a Port Adapter Guides Attaching PA-4T+ Port Adapter Interface Cables Installing the PA-4T+ Interface Cables Incorrect, cable upside down Replacing PA-4T+ Port Adapter Cables For a VIP2, use the following commands Router# copy running-config startup-config Using the Exec Command Interpreter Configuring the PA-4T+ Interfaces Cisco 7200 Series and Cisco uBR7200 Series Ports PA-4T+ Interface Port Address Example-Cisco uBR7246 PA-4T+ Interface Port Address Example-Cisco VIP2 Ports Cisco 7100 Series Ports Shutting Down an Interface Enter the shutdown command as follows Router# show interfaces serial 1/0 Conﬁgure additional interfaces as required Performing a Basic Conﬁguration Setting the Clock Rate Conﬁguring Timing Clock Signals Inverting the Clock Signal Inverting the Data Signal Conﬁguring Half-Duplex and Binary Synchronous Communications Conﬁguring Half-Duplex Checking the Conﬁguration Using show Commands to Verify the New Interface StatusConﬁguring Bisync Hardware is M4T Internet address is Using show Commands to Display Interface Information Checking the Configuration Router# show version VIP2 show interfaces Command Minute output rate 0 bits/sec, 0 packets/sec System image file is image-name, booted via tftp from Using ping and loopback Commands Checking the Configuration

Top Page Image Contents