Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems manual PA-4T+ Synchronous Serial Port Adapter Installation and Configuration

Models: PA-4T

1 76

Download 76 pages 35.25 Kb

Page 1

PA-4T+ Synchronous Serial Port Adapter Installation and Configuration

PA-4T+ Synchronous Serial Port Adapter Installation and Configuration

Product Number: PA-4T+(=)

Platforms Supported: Cisco 7200 Series, Cisco 7000 Series and Cisco 7500 Series with VIP2, Cisco uBR7200 Series, Cisco 7100 Series

Note If you ordered this port adapter as a spare, for your convenience Cisco has included a port adapter installation and conﬁguration note for the Catalyst 5000 series Route Switch Module/Versatile Interface Processor 2 (RSM/VIP2). Your port adapter is fully compatible with the RSM/VIP2.

Corporate Headquarters

Cisco Systems, Inc.

170 West Tasman Drive San Jose, CA 95134-1706

USA http://www.cisco.com Tel: 408 526-4000

800 553-NETS (6387) Fax: 408 526-4100

Text Part Number: 78-4159-07

Image 1

Cisco Systems manual PA-4T+ Synchronous Serial Port Adapter Installation and Configuration, Product Number PA-4T+=

Contents

Product Number PA-4T+= PA-4T+ Synchronous Serial Port Adapter Installation and ConfigurationCorporate Headquarters Copyright 1997-1999 Cisco Systems, Inc All rights reserved PA-4T+ Synchronous Serial Port Adapter Installation and ConfigurationPort Adapter Overview OverviewC H A P T E R Port Adapter Overview Note In the following examples, the PA-4T+ is displayed as Mx serialFigure 1-2 PA-4T Port Adapter-Faceplate View Router# show diag 3 SlotSynchronous Serial Overview Serial Interface Specifications Serial Interface SpeciﬁcationsPA-4T+ Receptacles and Cables Cables and PinoutsEIA-530 DTE mode with a DB-25 plug CAB-530MT= Figure 1-4 EIA/TIA-232 Adapter Cable Connectors EIA/TIA-232 ConnectionsPA-4T+ Receptacles and Cables V.35 Connections EIA/TIA-449 ConnectionsH1344a H1616aX.21 Connections PA-4T+ Port Adapter Cable PinoutsEIA-530 Connections Signal EIA/TIA-232 Adapter Cable SignalsSignal SignalSignal SignalPA-4T+ Port Adapter Cable Pinouts Router DTE EndSignal EIA/TIA-449 Adapter Cable SignalsSignal SignalSignal EIA-530 DTE Adapter Cable Signals CAB-530MT=Signal PA-4T+ Port Adapter Cable PinoutsSignal V.35 Adapter Cable SignalsSignal SignalLEDs PA-4T+ Port LEDs LEDsLED Label ColorObjectives PrefaceRelated Documentation Document OrganizationCisco Connection Online Documentation CD-ROM Tools and Parts Required Preparing for InstallationC H A P T E R Software and Hardware Requirements Note The minimum recommended VIP2 model is a VIP2-15 Preparing for InstallationSoftware and Hardware Requirements Safety Warnings Safety GuidelinesElectrical Equipment Guidelines Telephone Wiring GuidelinesPreventing Electrostatic Discharge Damage FCC Class B ComplianceMove the equipment farther away from the television or radio FCC Class B Compliance VIP2 and the PA-4T+ Port Adapter Installation OverviewC H A P T E R Figure 3-1 VIP2-15 or VIP2-40 with a PA-4T+ in Port Adapter Slot Installation Overviewdaughter Removing a Port Adapter Removing a Port AdapterInstalling a Port Adapter H3150 Carrier Upper edge Lower edgeH3152 Installation Overview Cisco 7200 Series and the PA-4T+ Port AdapterFigure 4-1 Cisco 7206 with a PA-4T+ Installed C H A P T E RRemoving a Port Adapter Note This adapter removal applies to any port or service adapterPort adapter handleInstalling a Port Adapter Figure 4-3 Handling a Port Adapter Installing a Port AdapterMetal carrier Printed circuit board SlotH6747 Port adapter lever locked positionInstallation Overview Cisco uBR7200 Series and the PA-4T+ Port AdapterC H A P T E R Cisco uBR7200 Series and the PA-4T+ Port AdapterPort adapters Removing a Port AdapterPort adapter retention clip in unlocked position H11518Figure 5-4 Handling a Port Adapter Removing a Port AdapterCisco uBR7200 Series and the PA-4T+ Port Adapter Inside slot guide PC board Installing a Port AdapterMetal carrier H11519Figure 5-6 Placing the Port Adapter Lever in the Locked Position Installing a Port AdapterH11517 16177Installing a Port Adapter Installation Overview Cisco 7100 Series and the PA-4T+ Port AdapterC H A P T E R Figure 6-1 Cisco 7120 Series Router-Port Adapter Slot 3 LocationRemoving a Port Adapter Removing a Port AdapterFigure 6-2 Cisco 7140 Series Router-Port Adapter Slot 4 Location Installing a Port Adapter Figure 6-3 Handling a Port Adapter Installing a Port AdapterRCVR GuidesXMTR Attaching PA-4T+ Port Adapter Interface Cables Installing the PA-4T+ Interface CablesC H A P T E R Correct Replacing PA-4T+ Port Adapter CablesIncorrect, cable upside down For a VIP2, use the following commands Page Using the EXEC Command Interpreter Configuring the PA-4T+ InterfacesC H A P T E R Cisco 7200 Series and Cisco uBR7200 Series Ports Identifying Port Adapter Slot and PA-4T+ Interface Port NumbersFigure 8-1 PA-4T+ Interface Port Address Example-Cisco uBR7246 Cisco 7200 Series and Cisco uBR7200 Series PortsFigure 8-2 PA-4T+ Interface Port Address Example-Cisco uBR7200 Series PA-4T+ port adapterprocessor VIP2 PortsCisco 7100 Series Ports Shutting Down an InterfaceStep 4 Enter the shutdown command as follows For a VIP2, use the following example Performing a Basic Conﬁguration Setting the Clock Rate Conﬁguring Timing Clock SignalsInverting the Clock Signal Conﬁguring NRZI Format Inverting the Data SignalSetting the Clock Rate Conﬁguring CRCs Conﬁguring Half-Duplex and Binary Synchronous CommunicationsConﬁguring Half-Duplex Checking the Conﬁguration Using show Commands to Verify the New Interface StatusConﬁguring Bisync show interfaces type slot/port commandUsing show Commands to Display Interface Information Using show Commands to Display Interface InformationChecking the Configuration The show version or show hardware command displays the conﬁguration of the system hardware the number of each port adapter type installed, the software version, the names and sources of conﬁguration ﬁles, and the boot images. Following is an example of the show version command Checking the Configuration VIP2 show interfaces CommandConfiguring the PA-4T+ Interfaces Using show Commands to Display Interface InformationLast reset from power-on G.703/E1 software, Version Checking the ConfigurationRouter# show version GEN1 uptime is 2 minutes System restarted by reloadUsing ping and loopback Commands Router# ping 10.10.10.10 Return Type escape sequence to abort Sending 5, 100-byte ICMP Echoes to 10.10.10.10, timeout is 2 seconds