Tripp Lite B006-VUA4-K-R owner manual Hardware Setup, Safety Instructions

Page 6

Hardware Setup

Safety Instructions

•Read all of these instructions. Save them for future reference.

•Follow all warnings and instructions marked on the device.

•Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result.

•Do not use the device near water.

•Do not place the device near, or over, radiators or heat registers. The device cabinet is provided with slots and openings to allow for adequate ventilation. To ensure reliable operation, and to protect against overheating, these openings must never be blocked or covered.

•The device should never be placed on a soft surface (bed, sofa, rug, etc.) as this will block its ventilation openings. Likewise, the device should not be placed in a built-in enclosure unless adequate ventilation has been provided.

•Never spill liquid of any kind on the device.

•Unplug the device from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

•The device should be operated from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.

•Do not allow anything to rest on the power cord or cables. Route the power cord and cables so that they cannot be stepped on or tripped over.

•If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the extension cord ampere rating. Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.

•Position system cables and power cables carefully; be sure that nothing rests on any cables.

•To help protect your system from sudden transient increases and decreases in electrical power, it is recommended that you plug your devices into a Tripp Lite Surge Suppressor,

Line Conditioner, or Uninterruptible Power Supply (UPS).

•When connecting or disconnecting power to hot-pluggable power supplies, observe the following guidelines:

—Install the power supply before connecting the power cable to the power supply. —Unplug the power cable before removing the power supply.

—If the system has multiple sources of power, disconnect power from the system by unplugging all power cables from the power supplies.

•Never push objects of any kind into or through cabinet slots. They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock.

•Do not attempt to service the device yourself. Refer all servicing to qualified service personnel.

6

201004198 93-2947.indd 6

4/23/2010 3:26:52 PM

Page 5 Page 7
Image 6
Page 5 Page 7
Contents RoHS FCC InformationTable of Contents Package ContentsConsole Requirements Supported Operating Systems FeaturesComputer Requirements VersionOrange when the KVM focus is on the corresponding port Front PanelBack Panel Hardware Setup Safety InstructionsRackmount Installation System InstallationPowering Off and Restarting Basic OperationPort Switching Manual Push-ButtonsPerforms a USB keyboard Alternate Hotkey Setting Mode Activation Command Mouse Port Switching FunctionalityHotkey Setting Mode HotkeysSwitching USB Focus Only to a Desired Port Switching KVM Focus Only to a Desired PortSwitching KVM Focus Only to the Next Port Switching USB Focus Only to the Next PortSwitching Audio Focus Only to a Desired Port Switching Audio Focus Only to the Next PortSkip Mode Initiate an Auto ScanInitiate an Auto Scan at a Desired Time Interval Alternate OSD Menu Activation Command List KVM SettingsUSB Keyboard/Mouse Reset Video SyncCommand to Ctrl, F12 Hotkey Command Summary TableAction Hotkey Command To Ctrl, CtrlOSD Main Screen Components Table OSD OperationOSD Main Screen ComponentIndividually Switch KVM, USB and Audio Focus via Keyboard Switch KVM, USB and Audio Focus Simultaneously via KeyboardSwitch KVM, USB and Audio Focus Simultaneously via Mouse OSD Main Page FunctionalityExiting the OSD Main Screen Individually Switch KVM, USB and Audio Focus via MouseNaming Ports F4 ScanF8 Logout OSD Settings Page FunctionalitySetting Description Is Scroll Lock, Scroll LockScan Duration ValuesComplete instructions on how to perform a firmware upgrade Mouse EmulationFirmware Upgrade Utility Settings Page. See page 21 for detailsClick Next Sun Keyboard Emulation AppendixMac Keyboard Emulation PC Keyboard Mac KeyboardOff Factory Default SettingsSetting Default EnglishSpecifications Feature SpecificationWarranty & Warranty Registration Regulatory Compliance Identification Numbers201004198 932947-EN
Top Page Image Contents