Tripp Lite B006-VUA4-K-R owner manual Rackmount Installation, System Installation

Page 7

Hardware Setup continued

•If the following conditions occur, unplug the device from the wall outlet and bring it to qualified service personnel for repair.

—The power cord or plug has become damaged or frayed. —Liquid has been spilled into the device.

—The device has been exposed to rain or water.

—The device has been dropped, or the cabinet has been damaged.

—The device exhibits a distinct change in performance, indicating a need for service.

—The device does not operate normally when the operating instructions are followed.

•Only adjust those controls that are covered in the operating instructions. Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair.

Rackmount Installation

Using the included rackmount hardware, attach the rackmount brackets to the KVM switch. Depending on whether you want to mount the KVM switch to the front or back of the rack, install the rackmount brackets to the front or back sides of the KVM switch. Using user- supplied screws, fasten the rackmount brackets to the rack.

System Installation

Refer to the steps and diagram to set up your KVM switch installation. Note: Before making any connections, make sure that power to all devices being connected to the KVM switch is turned off. Unplug the power cords of any computers that have the Keyboard Power On function.

8

2

3

3

4

1

7

5

8

1Connect your monitor to the HD15 Female console port on the back panel of the KVM switch.

2Connect your USB keyboard and USB mouse to the corresponding USB console ports on the back of the KVM switch. If you have a PS/2 keyboard and/or mouse, connect the included USB to (x2) PS/2 adapter cable to one of the USB console ports on the back of the unit, and then connect your PS/2 keyboard and/or mouse to the corresponding PS/2 connector(s) on the adapter cable. You can connect any combination of keyboard and mouse; USB – USB, PS/2 – PS/2 or USB – PS/2.

7

201004198 93-2947.indd 7

4/23/2010 3:26:53 PM

Page 6 Page 8
Image 7
Page 6 Page 8
Contents FCC Information RoHSPackage Contents Table of ContentsConsole Requirements Version FeaturesComputer Requirements Supported Operating SystemsFront Panel Orange when the KVM focus is on the corresponding portBack Panel Safety Instructions Hardware SetupSystem Installation Rackmount InstallationBasic Operation Powering Off and RestartingManual Push-Buttons Port SwitchingPerforms a USB keyboard Hotkeys Mouse Port Switching FunctionalityHotkey Setting Mode Alternate Hotkey Setting Mode Activation CommandSwitching USB Focus Only to the Next Port Switching KVM Focus Only to a Desired PortSwitching KVM Focus Only to the Next Port Switching USB Focus Only to a Desired PortSwitching Audio Focus Only to the Next Port Switching Audio Focus Only to a Desired PortInitiate an Auto Scan Skip ModeInitiate an Auto Scan at a Desired Time Interval Video Sync List KVM SettingsUSB Keyboard/Mouse Reset Alternate OSD Menu Activation CommandTo Ctrl, Ctrl Hotkey Command Summary TableAction Hotkey Command Command to Ctrl, F12Component OSD OperationOSD Main Screen OSD Main Screen Components TableOSD Main Page Functionality Switch KVM, USB and Audio Focus Simultaneously via KeyboardSwitch KVM, USB and Audio Focus Simultaneously via Mouse Individually Switch KVM, USB and Audio Focus via KeyboardF4 Scan Individually Switch KVM, USB and Audio Focus via MouseNaming Ports Exiting the OSD Main ScreenIs Scroll Lock, Scroll Lock OSD Settings Page FunctionalitySetting Description F8 LogoutValues Scan DurationMouse Emulation Complete instructions on how to perform a firmware upgradeSettings Page. See page 21 for details Firmware Upgrade UtilityClick Next PC Keyboard Mac Keyboard AppendixMac Keyboard Emulation Sun Keyboard EmulationEnglish Factory Default SettingsSetting Default OffFeature Specification SpecificationsRegulatory Compliance Identification Numbers Warranty & Warranty Registration201004198 932947-EN
Top Page Image Contents