Moxa Technologies PT-7728 user manual Configuring Email Warning, Event Type

Page 70

PT-7728 User’s Manual

Featured Functions

Configuring Email Warning

The Auto Email Warning function uses e-mail to alert the user when certain user-configured events take place.

Three basic steps are required to set up the Auto Warning function:

1.Configuring Email Event Types

Select the desired Event types from the Console or Web Browser Event type page (a description of each event type is given later in the Email Alarm Events setting subsection).

2.Configuring Email Settings

To configure PT-7728’s email setup from the serial, Telnet, or web console, enter your Mail Server IP/Name (IP address or name), Account Name, Account Password, Retype New Password, and the email address to which warning messages will be sent.

3.Activate your settings and if necessary, test the email

After configuring and activating your PT-7728’s Event Types and Email Setup, you can use the Test Email function to see if your e-mail addresses and mail server address have been properly configured.

Event Type

Event Types can be divided into two basic groups: System Events and Port Events. System Events are related to the overall function of the switch, whereas Port Events are related to the activity of a specific port.

System Events	Warning e-mail is sent when…
Switch Cold Start	Power is cut off and then reconnected.
Switch Warm Start	PT-7728 is rebooted, such as when network
	parameters are changed (IP address, subnet mask,
	etc.).
Power Transition (OnÆOff)	PT-7728 is powered down.
Power Transition (OffÆOn)	PT-7728 is powered up.
Configuration Change Activated	Any configuration item has been changed.
Authentication Failure	An incorrect password is entered.
Comm. Redundancy Topology	If any Spanning Tree Protocol switches have changed
Changed	their position (applies only to the root of the tree).
	If the Master of the Turbo Ring has changed or the
	backup path is activated.

3-56

Image 70

Contents Moxa PowerTrans Switch PT-7728 User’s Manual First Edition, February Moxa IncTrademarks Copyright NoticeDisclaimer Table of Contents Appendix a MIB Groups Appendix B Specifications ‰ Overview ‰ Package Checklist ‰ Software Features IntroductionSoftware Features Package ChecklistOverview Getting Started Serial Console Configuration 115200, None, 8, 1, VT100 PT-7728 User’s Manual Getting Started Configuration by Telnet Console Key FunctionPT-7728 User’s Manual Getting Started PT-7728 User’s Manual Getting Started Configuration by Web Browser Disabling Telnet and Browser Access Featured Functions Configuring Basic Settings System IdentificationPassword PasswordAccount Grant access to any host on a specific subnetwork Accessible IPGrant access to one host with a specific IP address Hosts That Need Access Input FormatDescription EnablePort NameSpeed NetworkFDX Flow Ctrl Switch Subnet Mask Auto IP ConfigurationSwitch IP Address Default GatewayCurrent Time TimeDaylight Saving Time Current DateSystem File Update-By Remote Tftp Firmware Files Path and Name Configuration Files Path and NameTftp Server IP/Name Log Files Path and NameSystem File Update-By Local Import/Export Factory DefaultUsing Port Trunking Port Trunking ConceptTrunk Type Configuring Port TrunkingTrunk Group Maximum of 4 trunk groups Available Ports/Member PortsSetting Description Configuring SnmpTrunk Table V1, V2c Read Community Snmp Read/Write SettingsSnmp Versions V1, V2c Write/Read CommunitySetting Description Factory Default 1st Trap Server IP/Name Setting Description Factory DefaultUsing Communication Redundancy Private MIB informationInitial setup for Turbo Ring or Turbo Ring Turbo Ring ConceptTurbo Ring with odd number switches Ring Coupling Configuration Determining the Redundant Path for Turbo RingSwitch B Dual-Homing Configuration for Turbo Ring Configuring Turbo Ring and Turbo RingConfiguring Turbo Ring Redundancy Protocol Now ActiveMaster/Slave Set as MasterCoupling Port Enable Ring CouplingCoupling Control Port Ring 1/2-1st Ring Port Status Ring 1/2-2nd Ring Port Status Enable RingRing 1/2-Status Coupling-ModeCoupling Mode Primary/Backup PortWhat is STP? STP/RSTP ConceptPT-7728 User’s Manual Featured Functions STP Requirements STP ConfigurationHow STP Works Port Speed Path Cost 802.1D Edition 802.1w-2001Differences between Rstp and STP STP ReconfigurationSTP Example Using STP on a Network with Multiple VLANs Protocol of Redundancy Configuring STP/RSTPRoot/Not Root Bridge PriorityHello Time sec Forwarding DelayEnable STP per Port Max. Age secWhat is Traffic Prioritization? Using Traffic PrioritizationConfiguration Limits of RSTP/STP Traffic Prioritization ConceptHow Traffic Prioritization Works Ieee 802.1p Priority Level Ieee 802.1D Traffic TypeTraffic Prioritization Differentiated Services DiffServ Traffic MarkingTraffic Queues Queuing Mechanism Configuring Traffic PrioritizationQoS Classification Inspect TOSTOS/DiffServ Mapping Setting Description FactoryCoS Mapping Inspect COSWhat is a VLAN? Using Virtual LANVirtual LAN Vlan Concept Managing a Vlan VLANs and the PowerTransBenefits of VLANs Communication Between VLANsSample Applications of VLANs using PT-7728 VLANs Tagged and Untagged MembershipPT-7728 User’s Manual Featured Functions Management Vlan ID Configuring Virtual LANVlan Settings Port TypeConcept of Multicast Filtering Using Multicast FilteringWhat is an IP Multicast? Vlan TableMulticast Filtering Benefits of MulticastNetwork without multicast filtering Query Mode Multicast Filtering and Moxa PowerTrans SwitchIgmp Internet Group Management Protocol Snooping Mode Network with multicast filteringGmrp Garp Multicast Registration Protocol Configuring Igmp SnoopingIgmp Multicast Filtering Static Multicast MACIgmp Snooping Settings Add Static Multicast MAC Gmrp enable Using Bandwidth ManagementConfiguring Gmrp Gmrp TableTraffic Rate Limiting Settings Configuring Bandwidth Management Broadcast Storm ProtectionIngress Static Port Lock Using Port Access ControlConfiguring Static Port Lock IeeeRadius Server Configuring IeeeDatabase Option Server Port802.1X Re-Authentication Local User Database SetupPort Access Control Table Using Auto WarningLocal User Database Setup Configuring Email Warning Event TypePort Events Email SetupMoxaPowerTransSwitch0001@SwitchLocation Mail Server IP/NameAccount Name Configuring Relay WarningPassword Setting Email AddressEvent Setup Configuring Line-Swap Fast Recovery Using Line-Swap-Fast-RecoveryUsing Set Device IP Override relay alarm settingsConfiguring Set Device IP Set up the connected devicesUsing Diagnosis Mirror PortMonitor by Switch Using MonitorPing Using the MAC Address Table Monitor by PortUsing Event Log MACUsing Syslog Syslog ServerPT-7728 User’s Manual Featured Functions MIB II.4 IP Group MIB II.1 System GroupMIB II.2 Interfaces Group MIB II.5 Icmp GroupMIB II.11 Snmp Group MIB II.10 Transmission GroupMIB II.17 dot1dBridge Group Public Traps Private TrapsTechnology Switch PropertiesInterface Power Optical Fiber 100BaseFXMechanical WarrantyEnvironmental