Moxa Technologies 5400 user manual Web Console Configuration Snmp Settings, IP Address Report

Page 35

Web Console Configuration

SNMP Settings

Community Name

Setting

Factory Default

Necessity

1 to 39 characters

public

Optional

(E.g., Support, 886-89191230 #300)

 

 

A community name is a plain-text password mechanism that is used to weakly authenticate queries to agents of managed network devices.

Contact

Setting

Factory Default

Necessity

1 to 39 characters

None

Optional

(E.g., Support, 886-89191230 #300)

 

 

 

 

 

The SNMP contact information usually includes an emergency contact name and telephone or pager number.

Location

Setting

Factory Default

Necessity

1 to 39 characters

None

Optional

(E.g., Floor 1, office 2)

 

 

 

 

 

Specify the location string for SNMP agents such as NPort. This string is usually set to the street address where the NPort is physically located.

IP Address Report

When NPort 5000 series products are used in a dynamic IP environment, users must spend more time with IP management tasks. For example, NPort works as a server (TCP or UDP), and the host, which acts as a client, must know the IP address of the server. If the DHCP server assigns a new IP address to the server, the host must take care of what happens when the IP changes.

NPort 5000 series products help out by periodically reporting their IP address to the IP location server, in case the dynamic IP has changed. The parameters shown below are used to configure the Auto IP report function. There are two ways to develop an “Auto IP report Server” to receive NPort’s Auto IP report.

1.Use NPort Administrator’s IP Address Report function.

2.Refer the Appendix E for the “Auto IP report protocol” to develop your own software.

Auto report to IP

Setting

Factory Default

Necessity

E.g., 192.168.1.1 or URL

None

Optional

(IP addresses of the form x.x.x.0 and

 

 

x.x.x.255 are invalid.)

 

 

Reports generated by the Auto report function will be automatically sent to this IP address.

Auto report to TCP port

Setting

Factory Default

Necessity

E.g., 4001

4002

Optional

 

 

 

Auto report period

 

 

 

 

 

Setting

Factory Default

Necessity

Time interval (in seconds)

10

Optional

 

 

 

NPort 5400 Series User’s Manual 5-9

Image 35
Contents Third Edition, May Series User’s ManualDisclaimer Copyright NoticeTrademarks Table of Contents Chapter IP Serial LIB Introduction Overview Package ChecklistProduct Features Introduction Product SpecificationsRegulatory Approvals Power RequirementsMechanical EnvironmentGetting Started Panel Layout Connecting the HardwarePanel Layout Getting Started Connecting the HardwareWiring Requirements Connecting the PowerGrounding NPort Connecting to the NetworkConnecting to a Serial Device LED IndicatorsThis chapter includes the following sections ConfigurationLCM Display Factory Default IP AddressDefault IP address Initializing NPort’s IP AddressDetailed Menu Options Initial IP Address ConfigurationButton Name Action Inact. time Delimiter Initial IP Address Configuration ARP NPort Administration SuiteTelnet Console NPort 5400 Series User’s Manual Initial IP Address Configuration Page Choosing the Proper Operation Mode TCP Server Mode Choosing the Proper Operation Mode TCP Client ModeUDP Mode Real COM ModeNPort 5400 Series User’s Manual Web Console Configuration Opening Your Browser Web Console Configuration Time zone Basic SettingsTime Server nameTime server Network SettingsSetting Factory Default Necessity ConsoleNPort 5400 Series User’s Manual Gateway IP AddressNetmask DNS server 1 / DNS sever IP ConfigurationIP Address Report Web Console Configuration Snmp SettingsPort alias Serial SettingsWeb Console Configuration Serial Parameters TCP alive check time Operating SettingsReal COM Mode Setting Factory Default Necessity To 99 min Min OptionalMax Connection 2 to Setting Factory Default Necessity To FF None OptionalMax Connection Max. ConnectionForce Transmit TCP Server ModeSetting Factory Default Necessity To 65535 ms Optional Max Connection 2 to Inactivity timeLocal TCP port Setting Factory Default Necessity 4001 RequiredCommand port Setting Factory Default Necessity 966 OptionalTCP Client Mode NPort 5400 Series User’s Manual TCP connection Destination IP addressDestination IP address 2/3/4 UDP Mode Local listen port Any host can access the NPort Accessible IP SettingsOnly one host of specific IP address can access the NPort Hosts on the specific subnet can access the NPortDCD changed Auto Warning SettingsEvent Type Trap Setting Factory Default Necessity Enable, Disable OptionalDSR changed MailSnmp Trap Server Auto warning E-mail and Snmp TrapMail Server Change Password Load Factory Default Page Configuring Windows Administrator Installing Windows Administrator Configuring Windows Administrator Configuration Broadcast Search Unlock Unlock Password ProtectionLock Lock Fixed Configuring NPort 5410/5430/5340IBlank FixedUpgrade Firmware Export/Import Add Target Select target from the list MonitorConfiguring Windows Administrator NPort 5400 Series User’s Manual Port Monitor On-line COM Mapping COM MappingConfiguring Windows Administrator Fast Flush only flush local buffer Off-line COM Mapping IP Location Configuring Windows Administrator Page IP Serial LIB How to install IP Serial Library? What is IP Serial Library?Why Use IP Serial Library? Inquiry IP Serial LIB Function GroupsExample Program IP Serial LIBPage Pinouts and Cable Wiring Ethernet Port Pinouts Serial Port Pinouts Port Pinout DiagramsDB9 Female to DB9 Male for NPort Cable Wiring DiagramsPinouts and Cable Wiring Ethernet Cables Serial CablesDB9 Female to DB25 Male for NPort Well Known Port Numbers TCP Socket Application ServiceUDP Socket Application Service IP MIB Icmp MIB Snmp Agent with MIB II & RS-232 like groupAddress Translation MIB System MIB Interfaces MIBWell Known Port Numbers Input Signal Table Output Signal TablePage Service Information Following services are provided Moxa Internet ServicesMoxa Product NPort Serial Number Problem Report FormService Information Product Return Procedure NPort 5400 Series User’s Manual D-5 Revision HistoryNPort 5400 Series User’s Manual Auto IP Report Protocol AP ID & Hardware ID Mapping Table Auto IP Report FormatInfo n ID List