Moxa Technologies 5400 user manual Web Console Configuration Serial Parameters

Page 37

Web Console Configuration

Serial Parameters

Check the serial communication parameters in your Serial Device’s user’s manual. You should set up NPort’s serial parameters with the same communication parameters used by your serial devices.

Baud rate

Setting

Factory Default

Necessity

50 bps to 230400 bps

115200 bps

Required

 

 

 

NPort supports baud rate setting from 50 bps to 230.4 Kbps.

Data bits

Setting

Factory Default

Necessity

5, 6, 7, 8

8

Required

 

 

 

When the user sets Data bits to 5 bits, the stop bits setting will automatically change to 1.5 bits.

Stop bits

Setting

Factory Default

Necessity

1, 2

1

Required

 

 

 

Stop bits will be set to 1.5 when Data bits is set to 5 bits.

Parity

Setting

Factory Default

Necessity

None, Even, Odd, Space, Mark

None

Required

 

 

 

Flow control

 

 

 

 

 

Setting

Factory Default

Necessity

None, RTS/CTS, DTR/DSR, Xon/Xoff

RTS/CTS

Required

 

 

 

FIFO

 

 

 

 

 

Setting

Factory Default

Necessity

Enable, Disable

Enable

Required

 

 

 

NPort’s serial ports provide a 16-byte FIFO both in the Tx and Rx directions. Disable the FIFO setting when your serial device does not have a FIFO to prevent data loss during communication.

Interface

Setting

Factory Default

Necessity

NPort 5210: RS-232 only

NPort 5210: RS-232

Required

NPort 5230:

NPort 5230:

Required

RS-232 for port 1

Port 1: RS-232

 

RS-422, 2-wire RS-485, 4-wire

Port 2: RS-485 2-wire

 

RS-485 for port 2

 

 

NPort 5400 Series User’s Manual 5-11

Image 37
Contents Third Edition, May Series User’s ManualTrademarks Copyright NoticeDisclaimer Table of Contents Chapter IP Serial LIB Introduction Product Features Package ChecklistOverview Introduction Product SpecificationsMechanical Power RequirementsEnvironment Regulatory ApprovalsGetting Started Panel Layout Connecting the HardwarePanel Layout Wiring Requirements Connecting the HardwareConnecting the Power Getting StartedConnecting to a Serial Device Connecting to the NetworkLED Indicators Grounding NPortThis chapter includes the following sections ConfigurationDefault IP address Factory Default IP AddressInitializing NPort’s IP Address LCM DisplayButton Name Action Initial IP Address ConfigurationDetailed Menu Options Inact. time Delimiter Initial IP Address Configuration ARP NPort Administration SuiteTelnet Console NPort 5400 Series User’s Manual Initial IP Address Configuration Page Choosing the Proper Operation Mode TCP Server Mode UDP Mode TCP Client ModeReal COM Mode Choosing the Proper Operation ModeNPort 5400 Series User’s Manual Web Console Configuration Opening Your Browser Web Console Configuration Time Basic SettingsServer name Time zoneSetting Factory Default Necessity Network SettingsConsole Time serverNPort 5400 Series User’s Manual Netmask IP AddressGateway DNS server 1 / DNS sever IP ConfigurationIP Address Report Web Console Configuration Snmp SettingsPort alias Serial SettingsWeb Console Configuration Serial Parameters Real COM Mode Operating SettingsSetting Factory Default Necessity To 99 min Min Optional TCP alive check timeMax Connection Setting Factory Default Necessity To FF None OptionalMax. Connection Max Connection 2 toSetting Factory Default Necessity To 65535 ms Optional TCP Server ModeForce Transmit Max Connection 2 to Inactivity timeCommand port Setting Factory Default Necessity 4001 RequiredSetting Factory Default Necessity 966 Optional Local TCP portTCP Client Mode NPort 5400 Series User’s Manual Destination IP address 2/3/4 Destination IP addressTCP connection UDP Mode Local listen port Only one host of specific IP address can access the NPort Accessible IP SettingsHosts on the specific subnet can access the NPort Any host can access the NPortEvent Type Auto Warning SettingsDCD changed DSR changed Setting Factory Default Necessity Enable, Disable OptionalMail TrapMail Server Auto warning E-mail and Snmp TrapSnmp Trap Server Change Password Load Factory Default Page Configuring Windows Administrator Installing Windows Administrator Configuring Windows Administrator Configuration Broadcast Search Lock Unlock Password ProtectionUnlock Blank Configuring NPort 5410/5430/5340IFixed Lock FixedUpgrade Firmware Export/Import Add Target Select target from the list MonitorConfiguring Windows Administrator NPort 5400 Series User’s Manual Port Monitor On-line COM Mapping COM MappingConfiguring Windows Administrator Fast Flush only flush local buffer Off-line COM Mapping IP Location Configuring Windows Administrator Page IP Serial LIB Why Use IP Serial Library? What is IP Serial Library?How to install IP Serial Library? Example Program IP Serial LIB Function GroupsIP Serial LIB InquiryPage Pinouts and Cable Wiring Ethernet Port Pinouts Serial Port Pinouts Port Pinout DiagramsPinouts and Cable Wiring Cable Wiring DiagramsEthernet Cables Serial Cables DB9 Female to DB9 Male for NPortDB9 Female to DB25 Male for NPort Well Known Port Numbers TCP Socket Application ServiceUDP Socket Application Service IP MIB Icmp MIB Snmp Agent with MIB II & RS-232 like groupAddress Translation MIB System MIB Interfaces MIBWell Known Port Numbers Input Signal Table Output Signal TablePage Service Information Following services are provided Moxa Internet ServicesService Information Problem Report FormMoxa Product NPort Serial Number Product Return Procedure NPort 5400 Series User’s Manual D-5 Revision HistoryNPort 5400 Series User’s Manual Auto IP Report Protocol Info n Auto IP Report FormatID List AP ID & Hardware ID Mapping Table