Moxa Technologies 5110 Series Initializing NPort 5110’s IP Address, Factory Default IP Address

Page 12

NPort 5110 Series User’s Manual

Initial IP Address Configuration

Initializing NPort 5110’s IP Address

1.Determine whether your NPort 5110 needs to use a Static IP or Dynamic IP (either DHCP or BOOTP application).

2.If NPort 5110 is used in a Static IP environment, you can use NPort 5110 Administration Suite, ARP, Web Console, Telnet Console, or Serial Console to configure the new IP address.

3.If NPort 5110 is used in a Dynamic IP environment, you can use NPort 5110 Administration Suite, Web Console, Telnet Console, or Serial Console to configure NPort 5110 to get an IP address dynamically with DHCP, DHCP/BOOTP, or BOOTP.

ATTENTION

Consult your network administrator on how to reserve a fixed IP address for your NPort 5110 in the MAC-IP mapping table when using a DHCP Server or BOOTP Server. In most applications, you should assign a fixed IP address to your NPort 5110.

Factory Default IP Address

NPort 5110 products are configured with the following default private IP address:

Default IP address:

192.168.127.254

(IP addresses of the form 192.168.xxx.xxx are referred to as private IP addresses, since it is not possible to directly access a device configured with a private IP address from a public network. For example, you would not be able to ping such a device from an outside Internet connection. NPort 5110 applications that require sending data over a public network, such as the Internet, require setting up the server with a valid public IP address, which can be leased from a local ISP.)

NPort 5110 Administration Suite

NPort 5110 Administration Suite consists of some useful utility programs that are used to configure and manage your NPort 5110s.

See Chapter 5 for details on how to install NPort 5110 Administration Suite, and how to use this suite of useful utilities to set up IP addresses and configure your NPort 5110 serial device servers.

ARP

You can make use of the ARP (Address Resolution Protocol) command to set up an IP address for your NPort 5110. The ARP command tells your computer to associate the NPort 5110’s MAC address with the intended IP address. You must then use Telnet to access the NPort 5110, at which point the device server’s IP address will be reconfigured.

ATTENTION

In order to use the ARP setup method, both your computer and NPort 5110 must be connected to the same LAN. Or, you may use a cross-over Ethernet cable to connect the NPort 5110 directly to your computer’s Ethernet card. Your NPort 5110 must be configured with the factory default IP address—192.168.127.254—before executing the ARP command, as described below.

3-2

Page 11 Page 13
Image 12
Page 11 Page 13
Contents NPort 5110 Series User’s Manual First Edition, DecemberNPort 5110 User’s Manual Copyright NoticeTrademarks DisclaimerTable of Contents Ethernet Port Pinouts Serial Port Pinouts Ethernet CablesIntroduction Package Checklist Product FeaturesOverview Product Specifications Panel Layout Connecting the Hardware Getting StartedConnecting the Hardware Connecting the PowerPanel Layout Connecting to the Network Connecting to a Serial DeviceLED Indicators LED Name LED Color LED FunctionInitial IP Address Configuration Factory Default IP Address NPort 5110 Administration SuiteDefault IP address Initializing NPort 5110’s IP AddressTelnet Console Page Page Serial Console 19200, n, 8 Page Page Choosing the Proper Operation Mode TCP Server Mode TCP Client ModeUDP Mode Real COM ModePair Connection Mode Ethernet Modem Mode Web Console Configuration Opening Your Browser NPort 5110 Series User’s Manual Web Console Configuration Basic Settings Web/Telnet ConsoleServer name Web ConsoleNetwork Settings IP configurationMethod Function Definition IP address NetmaskGateway DNS server 1 / DNS serverSnmp Settings IP Address ReportCommunity name ContactSerial Settings Auto report to IPAuto report to TCP port Auto report periodSerial Parameters Operating Settings Real COM ModeTCP alive check time Max connectionSetting Factory Default Necessity To FF hex None Optional Setting Factory Default Necessity To 65535 ms OptionalMax connection 2 to DelimiterTCP Server Mode Inactivity timeSetting Factory Default Necessity To FF None Optional Setting Factory Default Necessity 4001 Required Command portSetting Factory Default Necessity 966 Optional Local TCP portTCP Client Mode Delimiter Destination IP address Destination IP address 2/3/4TCP connect on UDP Mode Local listen port Pair Connection Slave Mode Pair Connection Master Mode Ethernet Modem Dial-inDial-out Disconnection request from local siteAT Commands Disconnection request from remote siteRegisters AT&DAccessible IP Settings TCP port Setting Factory Default Necessity 4001 RequiredAuto Warning Settings Auto Warning E-mail and Snmp TrapMail Server Event Type Snmp Trap ServerDCD changed DSR changedChange Password Load Factory DefaultsConfiguring Windows Administrator Overview Installing Windows Administrator ConfigurationInstalling Windows Administrator Page Page Page Configuration Broadcast Search Page Page Unlock Password Protection Lock UnlockBlank FixedConfiguring NPort Page Upgrade Firmware Export/Import Monitor Select Add Target Page Page Page Page Port Monitor COM Mapping On-line COM MappingOn-line COM Mapping Off-line COM MappingSelect COM Settings to modify COM No., default setting, etc Page Fast Flush only flush local buffer Page Page Off-line COM Mapping Select Apply changeIP Location Page IP Serial LIB What is IP Serial Library? Why Use IP Serial Library?How to install IP Serial Library IP Serial LIB Function Groups Example ProgramPinouts and Cable Wiring Port Pinout Diagrams Ethernet Port Pinouts Serial Port PinoutsDB9 Male RS-232 port pinouts for NPort Cable Wiring Diagrams Ethernet CablesTCP Socket Application Service Well Known Port NumbersUDP Socket Application Service NPort 5110 Series User’s Manual Well Known Port NumbersNPort 5110 Series User’s Manual Well Known Port Numbers Snmp Agents with MIB II & RS-232 Like Groups System MIB Interfaces MIB Address Translation MIBTCP MIB Snmp MIB Input Signal Table Output Signal Table Auto IP Report Protocol Auto IP Report Format Info nID List AP ID & Hardware ID Mapping TableService Information Moxa Internet Services Following services are providedProblem Report Form Moxa NPort Moxa Product NPort Serial NumberProduct Return Procedure
Top Page Image Contents