Moxa Technologies 5110 Series user manual IP address, Netmask, Gateway, DNS server 1 / DNS server

Page 28

NPort 5110 Series User’s Manual

Web Console Configuration

 

IP address

 

 

 

 

Setting

Factory Default

Necessity

 

 

E.g., 192.168.1.1

192.168.127.254

Required

 

 

(IP addresses of the form x.x.x.0 and

 

 

 

 

x.x.x.255 are invalid.)

 

 

 

An IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify and talk to each other over the network. Choose a proper IP address which is unique and valid in your network environment.

Netmask

Setting

Factory Default

Necessity

E.g., 255.255.255.0

255.255.255.0

Required

A subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out over the network, the NPort 5110 will use the subnet mask to check whether the desired TCP/IP host specified in the packet is on the local network segment. If the address is on the same network segment as the NPort 5110, a connection is established directly from the NPort 5110. Otherwise, the connection is established through the given default gateway.

Gateway

Setting

Factory Default

Necessity

E.g., 192.168.1.1

None

Optional

A gateway is a network gateway that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Internet service provider are gateway nodes. NPort 5110 needs to know the IP address of the default gateway computer in order to communicate with the hosts outside the local network environment. For correct gateway IP address information, consult the network administrator.

IP configuration

Setting

Factory Default

Necessity

Static

Static

Required

DHCP

 

 

DHCP/BOOTP

 

 

BOOTP

 

 

ATTENTION

In Dynamic IP environments, the firmware will retry 3 times every 30 seconds until network settings are assigned by the DHCP or BOOTP server. The Timeout for each try increases from 1 second, to 3 seconds, to 5 seconds.If the DHCP/BOOTP Server is unavailable, the firmware will use the default IP address (192.168.127.254), Netmask, and Gateway for IP settings.

DNS server 1 / DNS server 2

Setting

Factory Default

Necessity

E.g., 192.168.1.1

None

Optional

(IP addresses of the form x.x.x.0 and

 

 

x.x.x.255 are invalid.)

 

 

When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the website’s correct IP address, and then the computer uses the response to

5-6

Image 28
Contents NPort 5110 Series User’s Manual First Edition, DecemberNPort 5110 User’s Manual Copyright NoticeTrademarks DisclaimerTable of Contents Ethernet Port Pinouts Serial Port Pinouts Ethernet CablesIntroduction Product Features Package ChecklistOverview Product Specifications Panel Layout Connecting the Hardware Getting StartedConnecting the Power Connecting the HardwarePanel Layout Connecting to the Network Connecting to a Serial DeviceLED Indicators LED Name LED Color LED FunctionInitial IP Address Configuration Factory Default IP Address NPort 5110 Administration SuiteDefault IP address Initializing NPort 5110’s IP AddressTelnet Console Page Page Serial Console 19200, n, 8 Page Page Choosing the Proper Operation Mode TCP Server Mode TCP Client ModeReal COM Mode UDP ModePair Connection Mode Ethernet Modem Mode Web Console Configuration Opening Your Browser NPort 5110 Series User’s Manual Web Console Configuration Basic Settings Web/Telnet ConsoleServer name Web ConsoleIP configuration Network SettingsMethod Function Definition IP address NetmaskGateway DNS server 1 / DNS serverSnmp Settings IP Address ReportCommunity name ContactSerial Settings Auto report to IPAuto report to TCP port Auto report periodSerial Parameters Operating Settings Real COM ModeTCP alive check time Max connectionSetting Factory Default Necessity To FF hex None Optional Setting Factory Default Necessity To 65535 ms OptionalMax connection 2 to DelimiterTCP Server Mode Inactivity timeSetting Factory Default Necessity To FF None Optional Setting Factory Default Necessity 4001 Required Command portSetting Factory Default Necessity 966 Optional Local TCP portTCP Client Mode Delimiter Destination IP address 2/3/4 Destination IP addressTCP connect on UDP Mode Local listen port Pair Connection Slave Mode Pair Connection Master Mode Ethernet Modem Dial-inDial-out Disconnection request from local siteAT Commands Disconnection request from remote siteRegisters AT&DAccessible IP Settings TCP port Setting Factory Default Necessity 4001 RequiredAuto Warning E-mail and Snmp Trap Auto Warning SettingsMail Server Event Type Snmp Trap ServerDCD changed DSR changedChange Password Load Factory DefaultsConfiguring Windows Administrator Overview Installing Windows Administrator ConfigurationInstalling Windows Administrator Page Page Page Configuration Broadcast Search Page Page Unlock Password Protection Lock UnlockBlank FixedConfiguring NPort Page Upgrade Firmware Export/Import Monitor Select Add Target Page Page Page Page Port Monitor COM Mapping On-line COM MappingOn-line COM Mapping Off-line COM MappingSelect COM Settings to modify COM No., default setting, etc Page Fast Flush only flush local buffer Page Page Off-line COM Mapping Select Apply changeIP Location Page IP Serial LIB Why Use IP Serial Library? What is IP Serial Library?How to install IP Serial Library IP Serial LIB Function Groups Example ProgramPinouts and Cable Wiring Ethernet Port Pinouts Serial Port Pinouts Port Pinout DiagramsDB9 Male RS-232 port pinouts for NPort Cable Wiring Diagrams Ethernet CablesTCP Socket Application Service Well Known Port NumbersUDP Socket Application Service NPort 5110 Series User’s Manual Well Known Port NumbersNPort 5110 Series User’s Manual Well Known Port Numbers Snmp Agents with MIB II & RS-232 Like Groups System MIB Interfaces MIB Address Translation MIBTCP MIB Snmp MIB Input Signal Table Output Signal Table Auto IP Report Protocol Auto IP Report Format Info nID List AP ID & Hardware ID Mapping TableService Information Moxa Internet Services Following services are providedProblem Report Form Moxa NPort Moxa Product NPort Serial NumberProduct Return Procedure