Sun Microsystems 805-1797-10 manual Related Documents, Unix Commands

Page 10

Related Documents

The following documents contain topics that relate to the information in the Sun Quad FastEthernet PCI Adapter Installation and User's Guide.

Title

 

Part Number

 

 

Your system installation or service manual

(System dependent)

Solaris 2.x Handbook for

SMCC Peripherals

(Release dependent)

 

SunVTS User's Guide

 

(Release dependent)

 

 

Sun Quad FastEthernet 2.0 CD-Insert

804-5901

OpenBoot 3.x Command

Reference Manual

802-5837

 

 

 

 

UNIX Commands

This document may not include specific software commands or procedures. Instead, it may name software tasks and refer you to operating system documentation or the handbook that was shipped with your new hardware.

The type of information that you might need to use references for includes:

Shutting down the system

Booting the system

Configuring devices

Other basic software procedures

See one or more of the following:

TM

Solaris 2.x Handbook for SMCC Peripherals contains Solaris 2.x software commands.

TM

On-line AnswerBook for the complete set of documentation supporting the

4Solaris 2.x software environment.

Other software documentation that you received with your system.

ixSun Quad FastEthernet PCI Adapter Installation and User's Guide Revision A, August 1997

Image 10
Contents Revision A, August USA 650 960-1300 fax 650 Revision A, August Please Recycle Contents Running Diagnostics Tests Regulatory Compliance Statements IndexPage Preface How This Book Is OrganizedUnix Commands Related DocumentsTypographic Conventions Shell PromptsOrdering Sun Documents Table P-1SunExpress Contact InformationSun Welcomes Your Comments XiiPage Product Overview 1Sun Quad FastEthernet PCI adapterHardware and Software Requirements Features1Hardware and Software Requirements Checking the OpenBoot Prom Revision Level Displaying the OpenBoot Prom Revision LevelPage Using a text editor, add the following line to the end Installing the AdapterAdding an Entry to the driveraliases File Installing the Adapter Diagnostic Testing Verifying the InstallationExamining Network Activity Code Example 2-1 watch-net-allCommad Output Rebooting the System Perform a reconfiguration boot on the systemPage Configuring the Driver Software Installing the Driver SoftwareAt the command line, use the grep command to search Configuring the Host FilesEtc/hosts file Reboot your system Booting From the NetworkAt the ok prompt type Increasing TCP/IP Performance Post-Installation Procedures OptionalConfiguring Driver Parameters As superuser root, typeForcing Network Speed Between 10 Mbps and 100 Mbps TypeAuto-Negotiation Local-mac-address PropertyOk setenv local-mac-address? true Page Specifications Physical Dimensions Table A-1Physical DimensionsPerformance Specifications Power RequirementsTable A-2Power Requirements Table A-3Performance SpecificationsSpecifications Page Interface Signals Figure B-132-Pin RJ-45 ConnectorsPage Configuring the Quad FastEthernet Device Driver Parameters Internal TransceiverDriver Parameter Values and Definitions Table C-1qfe Driver Parameter, Status, and DescriptionsDefining the Current Status Qfe Driver Parameter, Status, and DescriptionsInter-Packet Gap Parameters Table C-2Read-Only Parameters Defining the Current StatusTable C-4Parameters Defining lancemode and ipg0 Packet after receiving a packetOperational Mode Parameters Table C-5Operational Mode ParametersTable C-6Back-to-back Packet Transmission Capability Defining the Number of Back-to-Back Packets to TransmitReporting Transceiver Capabilities Table C-7Read-Only Transceiver CapabilitiesReporting the Link Partner Capabilities Table C-8Read-Only Link Partner CapabilitiesSetting Parameters Using the ndd Utility Setting qfe Driver ParametersTo Specify the Device Instance for the ndd Utility Use the instance number to select the device To modify a parameter value, use the -setoptionUsing the ndd Utility in Interactive Mode To Set the Mode to Auto-Negotiation Select at least one of the five capabilities adv100fdxcapSetting Parameters in the /etc/system File Table C-9Setting Variables in the /etc/system FileSetting Parameters Using the qfe.conf File Setting ipg Driver Parameters Using a qfe.conf File Unit-address = 2,1 Fourth line in the previous exampleSet the ipg1 and ipg2 parameters for the above four devices Kernel/drv/qfe.conf fileRunning Diagnostics Tests Using the OpenBoot Prom FCode SelftestShut down the system Reset the systemType show-devsto display the list of devices Set the auto-boot?configuration parameter to true Reset and reboot the systemPage Regulatory Compliance Statements FCC Class a NoticeFCC Class B Notice DOC Class a Notice Avis DOC, Classe a DOC Class B Notice Avis DOC, Classe BDeclaration of Conformity EMCSafety Supplementary InformationPage Index Index-51