Sun Microsystems 805-1797-10 manual Configuring the Driver Software, Installing the Driver Software

Page 25

CHAPTER 3

Configuring the Driver Software

This chapter describes how to configure the driver software used by the Sun Quad FastEthernet PCI adapter.

Installing the Driver Software

The Sun Quad FastEthernet 2.0 CD-ROM contains the software required by the Sun Quad FastEthernet PCI adapter. Install the software driver packages as described in the CD insert. (Future revisions of the Sun Quad FastEthernet software will also work with your adapter.)

Before you can use the four channels of the adapter, you will need to create and edit system host files, as described in the next section.

Configuring the Host Files

After installing the Sun Quad FastEthernet driver software, you must create a hostname.qfe<num> file for the adapter's Ethernet interfaces. You must also create both an IP address and a host name for its Ethernet interfaces in the /etc/hosts file.

1.At the command line, use the grep command to search the

/etc/path_to_inst file for qfe devices.

#grep qfe /etc/path_to_inst "/pci@1f,2000/pci@2/SUNW,qfe@0,1" 4 "qfe" "/pci@1f,2000/pci@2/SUNW,qfe@1,1" 5 "qfe" "/pci@1f,2000/pci@2/SUNW,qfe@2,1" 6 "qfe"

11

Image 25
Contents Revision A, August USA 650 960-1300 fax 650 Revision A, August Please Recycle Contents Running Diagnostics Tests Index Regulatory Compliance StatementsPage How This Book Is Organized PrefaceRelated Documents Unix CommandsShell Prompts Typographic ConventionsTable P-1SunExpress Contact Information Ordering Sun DocumentsXii Sun Welcomes Your CommentsPage 1Sun Quad FastEthernet PCI adapter Product OverviewHardware and Software Requirements Features1Hardware and Software Requirements Displaying the OpenBoot Prom Revision Level Checking the OpenBoot Prom Revision LevelPage Using a text editor, add the following line to the end Installing the AdapterAdding an Entry to the driveraliases File Installing the Adapter Diagnostic Testing Verifying the InstallationExamining Network Activity Code Example 2-1 watch-net-allCommad Output Perform a reconfiguration boot on the system Rebooting the SystemPage At the command line, use the grep command to search Installing the Driver SoftwareConfiguring the Driver Software Configuring the Host FilesEtc/hosts file Reboot your system Booting From the NetworkAt the ok prompt type Configuring Driver Parameters Post-Installation Procedures OptionalIncreasing TCP/IP Performance As superuser root, typeType Forcing Network Speed Between 10 Mbps and 100 MbpsLocal-mac-address Property Auto-NegotiationOk setenv local-mac-address? true Page Table A-1Physical Dimensions Specifications Physical DimensionsTable A-2Power Requirements Power RequirementsPerformance Specifications Table A-3Performance SpecificationsSpecifications Page Figure B-132-Pin RJ-45 Connectors Interface SignalsPage Internal Transceiver Configuring the Quad FastEthernet Device Driver ParametersTable C-1qfe Driver Parameter, Status, and Descriptions Driver Parameter Values and DefinitionsQfe Driver Parameter, Status, and Descriptions Defining the Current StatusTable C-2Read-Only Parameters Defining the Current Status Inter-Packet Gap ParametersPacket after receiving a packet Table C-4Parameters Defining lancemode and ipg0Table C-5Operational Mode Parameters Operational Mode ParametersReporting Transceiver Capabilities Defining the Number of Back-to-Back Packets to TransmitTable C-6Back-to-back Packet Transmission Capability Table C-7Read-Only Transceiver CapabilitiesTable C-8Read-Only Link Partner Capabilities Reporting the Link Partner CapabilitiesSetting Parameters Using the ndd Utility Setting qfe Driver ParametersTo Specify the Device Instance for the ndd Utility To modify a parameter value, use the -setoption Use the instance number to select the deviceUsing the ndd Utility in Interactive Mode Select at least one of the five capabilities adv100fdxcap To Set the Mode to Auto-NegotiationTable C-9Setting Variables in the /etc/system File Setting Parameters in the /etc/system FileSetting Parameters Using the qfe.conf File Unit-address = 2,1 Fourth line in the previous example Setting ipg Driver Parameters Using a qfe.conf FileKernel/drv/qfe.conf file Set the ipg1 and ipg2 parameters for the above four devicesUsing the OpenBoot Prom FCode Selftest Running Diagnostics TestsShut down the system Reset the systemType show-devsto display the list of devices Reset and reboot the system Set the auto-boot?configuration parameter to truePage FCC Class a Notice Regulatory Compliance StatementsFCC Class B Notice DOC Class B Notice Avis DOC, Classe B DOC Class a Notice Avis DOC, Classe aEMC Declaration of ConformitySupplementary Information SafetyPage Index-51 Index