Sun Microsystems 805-1797-10 manual Running Diagnostics Tests

Page 6

Increasing TCP/IP Performance 14

Forcing Network Speed Between 10 Mbps and 100 Mbps 15

Auto-Negotiation 16

local-mac-address Property 16

A.Specifications 19 Physical Dimensions 19 Power Requirements 20 Performance Specifications 20

B.Interface Signals 23

C.

Configuring the Quad FastEthernet Device Driver Parameters 25

 

Internal Transceiver 25

 

Driver Parameter Values and Definitions 26

 

 

Defining the Current Status

27

 

 

 

Inter-Packet Gap Parameters

28

 

 

 

Defining an Additional Delay Before Transmitting a Packet Using

 

 

lance_mode and ipg0

29

 

 

 

 

Operational Mode Parameters

30

 

 

 

Defining the Number of Back-to-Back Packets to Transmit 31

 

 

Reporting Transceiver Capabilities 31

 

 

 

Reporting the Link Partner Capabilities

32

 

 

Setting qfe Driver Parameters

33

 

 

 

 

Setting Parameters Using the ndd Utility

33

 

 

SettingH

Parameters in the /etc/system File

37

 

 

Setting the ipg1 and ipg2 Parameters in the /etc/system File 38

 

 

Setting Parameters Using the qfe.conf File

38

 

 

Setting ipg Driver Parameters Using a qfe.conf File 39

 

D.

Running Diagnostics Tests

41

 

 

 

 

 

Using the OpenBoot PROM FCode Selftest 41

v

Sun Quad FastEthernet PCI Adapter Installation and User's Guide Revision A, August 1997

Image 6
Contents Revision A, August USA 650 960-1300 fax 650 Revision A, August Please Recycle Contents Running Diagnostics Tests Regulatory Compliance Statements IndexPage Preface How This Book Is OrganizedUnix Commands Related DocumentsTypographic Conventions Shell PromptsOrdering Sun Documents Table P-1SunExpress Contact InformationSun Welcomes Your Comments XiiPage Product Overview 1Sun Quad FastEthernet PCI adapterFeatures Hardware and Software Requirements1Hardware and Software Requirements Checking the OpenBoot Prom Revision Level Displaying the OpenBoot Prom Revision LevelPage Installing the Adapter Using a text editor, add the following line to the endAdding an Entry to the driveraliases File Installing the Adapter Verifying the Installation Diagnostic TestingExamining Network Activity Code Example 2-1 watch-net-allCommad Output Rebooting the System Perform a reconfiguration boot on the systemPage Configuring the Driver Software Installing the Driver SoftwareAt the command line, use the grep command to search Configuring the Host FilesEtc/hosts file Booting From the Network Reboot your systemAt the ok prompt type Increasing TCP/IP Performance Post-Installation Procedures OptionalConfiguring Driver Parameters As superuser root, typeForcing Network Speed Between 10 Mbps and 100 Mbps TypeAuto-Negotiation Local-mac-address PropertyOk setenv local-mac-address? true Page Specifications Physical Dimensions Table A-1Physical DimensionsPerformance Specifications Power RequirementsTable A-2Power Requirements Table A-3Performance SpecificationsSpecifications Page Interface Signals Figure B-132-Pin RJ-45 ConnectorsPage Configuring the Quad FastEthernet Device Driver Parameters Internal TransceiverDriver Parameter Values and Definitions Table C-1qfe Driver Parameter, Status, and DescriptionsDefining the Current Status Qfe Driver Parameter, Status, and DescriptionsInter-Packet Gap Parameters Table C-2Read-Only Parameters Defining the Current StatusTable C-4Parameters Defining lancemode and ipg0 Packet after receiving a packetOperational Mode Parameters Table C-5Operational Mode ParametersTable C-6Back-to-back Packet Transmission Capability Defining the Number of Back-to-Back Packets to TransmitReporting Transceiver Capabilities Table C-7Read-Only Transceiver CapabilitiesReporting the Link Partner Capabilities Table C-8Read-Only Link Partner CapabilitiesSetting qfe Driver Parameters Setting Parameters Using the ndd UtilityTo Specify the Device Instance for the ndd Utility Use the instance number to select the device To modify a parameter value, use the -setoptionUsing the ndd Utility in Interactive Mode To Set the Mode to Auto-Negotiation Select at least one of the five capabilities adv100fdxcapSetting Parameters in the /etc/system File Table C-9Setting Variables in the /etc/system FileSetting Parameters Using the qfe.conf File Setting ipg Driver Parameters Using a qfe.conf File Unit-address = 2,1 Fourth line in the previous exampleSet the ipg1 and ipg2 parameters for the above four devices Kernel/drv/qfe.conf fileRunning Diagnostics Tests Using the OpenBoot Prom FCode SelftestReset the system Shut down the systemType show-devsto display the list of devices Set the auto-boot?configuration parameter to true Reset and reboot the systemPage Regulatory Compliance Statements FCC Class a NoticeFCC Class B Notice DOC Class a Notice Avis DOC, Classe a DOC Class B Notice Avis DOC, Classe BDeclaration of Conformity EMCSafety Supplementary InformationPage Index Index-51