Sun Microsystems 6U manual Refer to the server’s documentation for the procedure

Page 52

The hot-swapLED shows whether the adapter has been activated.

If the hot-swap LED is OFF (unlit), the I/O slots in the server have been set to full hot swap and the adapter has been activated. Go to Step 15.

If the hot-swap LED is ON, then the I/O slots in the server have been set to basic hot swap. You must use software commands to activate the I/O card. Go to Step 11.

Note You should also use the hot-swap LEDs on the server when installing the adapter. For example, Netra ct servers contain an OK to Remove LED ( ) on the system status panel that is used like the hot-swap LED on this adapter. Refer to your system’s service manual for a description on how the hot-swap LEDs are used during a hot-swap installation.

11.Remove the wrist strap from the chassis and from your wrist.

12.Log in to the server.

Refer to the server’s documentation for the procedure.

13.At the terminal prompt, type the hot-swap software commands to identify and attach the adapter to the server.

These commands may be specific to the server’s hot-swap software. Refer to the server’s documentation for the correct commands and procedures.

For example, if you are installing the adapter into a Netra ct server, you would use the cfgadm pci command to list the attachment point IDs in the server. On a Netra ct 800 server, you should see feedback similar to the following:

# cfgadm pci

 

 

 

 

Ap_Id

Type

Receptacle

Occupant

Condition

pci_pci0:cpci_slot2

unknown

empty

unconfigured

unknown

pci_pci0:cpci_slot3

stpcipci/fhs

connected

configured

ok

pci_pci0:cpci_slot4

stpcipci/fhs

connected

configured

ok

pci_pci0:cpci_slot5

unknown

empty

unconfigured

unknown

pci_pci0:cpci_slot6

unknown

empty

unconfigured

unknown

pci_pci0:cpci_slot7

unknown

empty

unconfigured

unknown

pci_pci0:cpci_slot8

stpcipci/fhs

connected

configured

ok

 

 

 

 

 

Once you have identified the attachment point ID on the Netra ct server, you can use the following commands to attach the adapter to the server:

#cfgadm -c connect attachment-point-id

#cfgadm -c configure attachment-point-id

34 Sun Quad FastEthernet 6U CompactPCI Adapter Installation and User’s Guide • June 2000

Image 52
Contents Sun Microsystems, Inc San Antonio Road Palo Alto, CA Please Recycle Regulatory Compliance Statements FCC Class a NoticeICES-003 Class a Notice Avis NMB-003, Classe a Bsmi Class a Notice Page Contents Installing the Front-Access Adapter Configuring the Network SoftwareSpecifications Removing and Replacing the AdapterTesting the Adapter IndexFigures Figure A-1 Operation Specifications TablesPage Preface How This Book Is OrganizedTypographic Conventions Using Unix CommandsTable P-1Typographic Conventions Shell Prompts Related DocumentationTable P-2Shell Prompts Table P-3Related DocumentationOrdering Sun Documentation Accessing Sun Documentation OnlineSun Welcomes Your Comments Overview Sun Quad FastEthernet 6U CompactPCI Adapter Product Description Front cardFeatures Installation Methods Overview of the Installation ProcedureModels of Hot Swap Installing the Rear-Access Adapter 1Rear-Access Installation OverviewInstalling the Front-Access Adapter 2Front-Access Installation OverviewInstalling the Rear-Access Adapter Contents of the Ship Kit Preparing for the InstallationTools and Equipment Needed Selecting a CompactPCI Slot Pair in the System 1CompactPCI Slot Pairs in a Sun Netra ct 800 Server Top ViewInstalling the Rear-Access Adapter in Hot-Swap Mode Determining the Installation TypeTo Install the Rear Transition Card 2Location of the Rear Transition Card’s Ejection LeversLocking mechanism TabsTabs 6Closing the Ejection Levers Two Types of Levers Cutouts Tabs To Install the Rear-Access Front Card Locate the slot where you plan to install the front card9Location of the Front Card’s Ejection Levers Page Remove the wrist strap from the chassis and from your wrist Log in to the server # cfgadm pciInstalling the Rear-Access Adapter in Cold-Swap Mode To Power Off the ServerTo Install the Rear Transition Card To Install the Rear-Access Front Card Remove the wrist strap from the chassis and from your wrist To Power On the Server Connecting the Cables to the Rear Transition Card To Connect the Cables to the Rear Ethernet PortsInstalling the Front-Access Adapter Selecting a CompactPCI Slot in the System Installing the Front-Access Adapter in Hot-Swap Mode To Install the Front-Access Adapter in Hot-Swap ModeTop Adapter Ejection levers in the locked position 2Opening the Ejection Levers Two Types of Levers 4Location of the Ejection Lever Tabs Two Types of Levers 7Location of the Front-Access Adapter’s Hot-Swap LED Refer to the server’s documentation for the procedure Remove the wrist strap from the chassis and from your wrist Installing the Front-Access Adapter in Cold-Swap Mode To Install the Front-Access Adapter in Cold- Swap Mode Remove the wrist strap from the chassis and your wrist Installing the Front-Access Adapter Connecting the Cables to Front-Access Adapter To Connect the Cables to the Front-Access Ethernet PortsConfiguring the Network Software At the terminal prompt, use the grep command to search Etc/pathtoinst file for qfe devicesConfiguring the Network Software # cat /etc/inet/hosts Activate the new qfe interfaces using the ifconfig command Autonegotiation ProtocolSetting the local-mac-address Property Log in to the system as superuser# eeprom local-mac-address\?=true Booting the System Over a Sun Quad FastEthernet Interface To Boot the System Over the NetworkSelect the qfe device that you want to use as a boot device Press the Return key to boot the system over the qfe devicePage Specifications Ethernet Port Locations Descriptions Figure A-1RJ-45 Ethernet Port LocationsOperation Specifications Table A-2Operation SpecificationsPhysical Dimensions of the Rear-Access Adapter Physical DimensionsTable A-3Physical Dimensions Rear-Access Environmental Specifications Physical Dimensions of the Front-Access AdapterTable A-4Physical Dimensions Front-Access Table A-5Environmental SpecificationsPower Requirements Table A-6Power RequirementsConfiguring Sun Quad FastEthernet Device Driver Parameters Sun Quad FastEthernet Device Driver Parameters Hardware OverviewDevice Driver Parameter Values and Definitions Table B-1qfe Driver Parameters, Status, and DescriptionsInterpacket Gap Parameters Parameters that Define the Current StatusTable B-2Read-Only Parameters Defining the Current Status Defining an Additional Delay Before Transmitting a Packet Table B-4Parameters Defining lancemode and ipg0Operational Mode Parameters Table B-5Operational Mode ParametersDefining the Number of Back-to-Back Packets to Transmit Parameters That Report Transceiver CapabilitiesTable B-6Back-to-Back Packet Transmission Capability Table B-7Read-Only Transceiver CapabilitiesParameters That Report the Link Partner Capabilities Table B-8Read-Only Link Partner CapabilitiesSetting the qfe Device Driver Parameters Using the ndd Utility to Set and Display ParametersTo Specify the Device Instance for the ndd Utility Using the ndd Utility in Noninteractive Mode To modify a parameter value, use the -setoption# ndd /dev/qfe \? Using the ndd Utility in Interactive Mode Type q to exit interactive modeSetting Forced Mode Using the ndd Utility To Enable Autonegotiation Using the ndd Utility Setting Parameters Using the qfe.conf File Table B-9qfe.conf File ParametersTo Set Driver Parameters By Creating a qfe.conf File Log in to the systemSave the qfe.conf file Removing and Replacing Adapter Use the ifconfig command to disable the qfe interfaces To Disable the Network Interfaces and Remove the AdapterDisabling the Network Interfaces and Removing the Adapter Appendix C Removing and Replacing the Adapter Replacing the Adapter and Activating the Network Interfaces Activate the qfe interfaces using the ifconfig commandTo Replace the Adapter and Activate the Network Interfaces Testing the Adapter Using the SunVTS Diagnostic Software Table D-1SunVTS DocumentationUsing the OpenBoot Prom FCode Self-Test To Run the FCode Self-Test DiagnosticReset the system to activate these parameter changes Ok setenv diag-switch? false ok setenv auto-boot? true Reset and reboot the system Index Creating, 43 editing, 42 examples LEDQfe.conf file

6U specifications

Sun Microsystems, a prominent player in the computing industry, made significant contributions to the development of high-performance hardware and software solutions. One of the notable products from the company is the 6U form factor, which refers to a specific standard for rack-mounted equipment. The 6U standard is particularly relevant in the context of server architecture, storage solutions, and other critical systems used in enterprise environments.

The 6U form factor typically stands at 10.5 inches in height, accommodating various configurations of hardware components while ensuring a compact footprint. This size makes it ideal for data centers and server rooms, where space is often at a premium. Sun Microsystems effectively utilized this form factor in its server lineup, catering to performance and density requirements.

A defining feature of Sun Microsystems' 6U models is their modular architecture. These servers support a range of powerful processors, including the UltraSPARC series, renowned for their high processing capabilities and energy efficiency. The use of the UltraSPARC architecture allows for robust multitasking and parallel processing, making these systems suitable for demanding applications such as database management and enterprise resource planning.

Moreover, Sun Microsystems integrated advanced memory technologies within their 6U designs. The servers support large amounts of RAM, utilizing technologies like ECC (Error-Correcting Code) memory to enhance data integrity. This is crucial for mission-critical applications where data loss can result in substantial operational impact.

In terms of connectivity, the 6U form factor features a variety of interfaces, including high-speed Ethernet ports, Fibre Channel connections, and USB ports. These options enable seamless integration into existing network infrastructures, facilitating efficient data transfer and storage management.

Storage solutions within the 6U framework include support for multiple RAID configurations and high-capacity disk drives. Sun Microsystems provided options for both SSD and traditional HDD storage, allowing organizations to tailor their systems to meet specific performance and capacity needs.

In addition to hardware characteristics, Sun Microsystems placed a strong emphasis on software compatibility. Their systems were designed to run a variety of operating systems, including Solaris, Linux, and Windows, thereby providing flexibility for enterprises to deploy their preferred software environments.

Overall, the 6U form factor from Sun Microsystems symbolizes the company's commitment to delivering high-performance, reliable, and scalable computing solutions. By combining innovative technology with practical design, Sun Microsystems created servers that met the diverse needs of businesses and paved the way for advancements in enterprise computing.